|
Home > Archive > Data Storage > February 2005 > Probs MSA1000, "I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed"
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
Probs MSA1000, "I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed"
|
|
| Daniel Schwager 2005-02-04, 7:45 am |
| Hi,
we have a problem with a HP MSA1000.
We start to install the MSA1000, but
when conntecting to to CLI we got the following errors
the whole time.
Maybe somebody can help us ?
Do somebody know the meaning of the error (we haven't found it any hp-manuel)
Do somebody know a way to track down this problem ?
Thanks for helping
regards
Danny
> Starting ICL links and beginning redundancy negotiation.
> PCI ICL link has been enabled.
> Starting ICL negotiation . . .
> NVRAM Contents:
> backplane:
> checksum offset = 118
> iteration offset = 121
> chassis name = VJ
> world wide name = 500805F3000005C0
> chassis serial num = 9J140000L2GJ
> backplane serial num = P3442XAH9HX268
> factory:
> board serial num = P56350B9IMX0B9
> Startup complete.
>
> * MSA1000 Command Line Interface *
>
> CLI> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 3
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 2
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 1
> setupICL_Link: failed to receive serial ICL info message.
> setupRedundancy: failed to negotiate redundancy.
> Redundant controller has been killed.
>
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 3
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 2
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 1
> I2C_Read_Chunk: Device = EMU, I2C_SetAddress() failed.
> I2C_Read: Resetting I2C bus for device = EMU, retry = 0
> I2C_Read: Device = EMU, I2C_Read_Chunk() failed.
> ERROR: failed on do_i2c_emu_command().
>
------------------------------------------------------------
DT Netsolution GmbH - Talaeckerstr. 30 - D-70437 Stuttgart
Tel: +49-711-849910-32 Fax: +49-711-849910-932
WEB: http://www.dtnet.de/ email: daniel.schwager@dtnet.de
| |
| Rob Turk 2005-02-04, 5:46 pm |
| "Daniel Schwager" <Daniel.Schwager@dtnet.de> wrote in message
news:42033B31.FA6CAC@dtnet.de...[vbcol=seagreen]
> Hi,
>
> we have a problem with a HP MSA1000.
>
> We start to install the MSA1000, but
> when conntecting to to CLI we got the following errors
> the whole time.
>
> Maybe somebody can help us ?
> Do somebody know the meaning of the error (we haven't found it any
> hp-manuel)
> Do somebody know a way to track down this problem ?
>
> Thanks for helping
>
> regards
>
> Danny
I2C is a serial protocol inside the machine between chips and subsystems
internally. The message probably means that the internal subsystems can no
longer talk to eachother. That's most likely a hardware failure, so get HP
to service it.
Rob
|
|
|
|
|