| Sylvain YVON 2006-05-08, 1:12 pm |
| Hi all,
I am looking for some help with the configuration of my iscsi
connection.
We have an Infortrend Eonstor iscsi with luns we want to access via a
Qlogic card in a HP Prolient under RHEL 4 running 2.6.9-34.ELsmp
kernel.
All is fine when I run the iscli tool. The qlogic card is found, I was
able to attach a target (automatically discovered after a few minutes)
HBA description in iscli :
1. HBA Model: QLA4010 HBA Serial Number: FS20604B16489 HBA Port:
0
iSCSI Name: iqn.2000-04.com.qlogic:qla4010.fs20604b16489
Alias:
IP Address: 192.168.1.51 Instance #: 0
Target description in iscli :
Target ID: 2 IP: 192.168.1.30 Port: 3260
ISCSI Name: iqn.2002-10.com.infortrend:raid.sn6792085.00
Alias:
State: Session Active
The problem is that although the session is active, we "Cannot obtain
Lun Infomation for this target."
So I enabled the debugging logs before launching iscli and got :
- at launch :
May 8 16:18:47 sh-prod-01 kernel: scsi2: qla4extioctl_get_isns_server:
GET ISNS SERVICE STATUS = 0x0000 "DISABLED"
May 8 16:18:47 sh-prod-01 kernel: scsi3: qla4xxx_mailbox_command: ****
FAILED, cmd = 00000021, sts = 00004005 ****
May 8 16:18:47 sh-prod-01 kernel: 0x00 mailbox[0] = 0x00004005
May 8 16:18:47 sh-prod-01 kernel: 0x04 mailbox[1] = 0x00000002
May 8 16:18:47 sh-prod-01 kernel: 0x08 mailbox[2] = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0x0C mailbox[3] = 0x04000000
May 8 16:18:47 sh-prod-01 kernel: 0x10 mailbox[4] = 0x00000204
May 8 16:18:47 sh-prod-01 kernel: 0x14 mailbox[5] = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0x18 mailbox[6] = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0x1C mailbox[7] = 0x00149AA7
May 8 16:18:47 sh-prod-01 kernel: 0x20 flash_address = 0x00040203
May 8 16:18:47 sh-prod-01 kernel: 0x24 flash_data = 0x00000011
May 8 16:18:47 sh-prod-01 kernel: 0x28 ctrl_status = 0x00000004
May 8 16:18:47 sh-prod-01 kernel: 0x2C nvram = 0x00000008
May 8 16:18:47 sh-prod-01 kernel: 0x38 req_q_in = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0x3C rsp_q_out = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0x50 ext_hw_conf = 0x00001916
May 8 16:18:47 sh-prod-01 kernel: 0x58 port_ctrl = 0x00000C1F
May 8 16:18:47 sh-prod-01 kernel: 0x5C port_status = 0x0001D61D
May 8 16:18:47 sh-prod-01 kernel: 0x80 req_q_out = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: 0xE0 gp_out = 0x00000003
May 8 16:18:47 sh-prod-01 kernel: 0xE4 gp_in = 0x0000000E
May 8 16:18:47 sh-prod-01 kernel: 0xFC port_err_status = 0x00000000
May 8 16:18:47 sh-prod-01 kernel: scsi3: qla4extioctl_get_isns_server:
GET ISNS SERVICE STATUS cmnd failed
- when querying luns :
May 8 16:19:41 sh-prod-01 kernel: qla4xxx 0000:05:07.1: DDB[2] MB0
4000 Tot 1 Next 0 State 0004 ConnErr 00000000 192.168.1.30:3260
"iqn.2002-10.com.infortrend:raid.sn6792085.00"
May 8 16:19:41 sh-prod-01 kernel: scsi2: qla4extioctl_scsi_passthru:
device (b0,t1) not in active state
I have been looking for some indications about these messages for hours
without finding anything, including the qlogic support site.
The driver compiled without any error, including the isns object file.
Here is my lsmod :
qla4xxx 225084 4
md5 8001 1
ipv6 240225 20
parport_pc 27905 0
lp 15405 0
parport 37641 2 parport_pc,lp
autofs4 22597 0
i2c_dev 14273 0
i2c_core 25921 1 i2c_dev
sunrpc 142757 1
button 10449 0
battery 12869 0
ac 8773 0
ohci_hcd 23889 0
hw_random 9557 0
tg3 95173 0
floppy 58065 0
dm_snapshot 20837 0
dm_zero 6337 0
dm_mirror 28449 0
ext3 118729 2
jbd 59481 1 ext3
dm_mod 59973 6 dm_snapshot,dm_zero,dm_mirror
cciss 57989 3
sd_mod 20545 0
scsi_mod 116941 3 qla4xxx,cciss,sd_mod
I would really appreciate some help or direction.
Thanks
Sylvain
|