|
Home > Archive > Voice over IP Cisco > December 2005 > PRI between CCM (3725) and Nortel M1
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
PRI between CCM (3725) and Nortel M1
|
|
| Sullivan, Gary, GREENWICH, 2005-12-29, 7:45 am |
| We have a PRI between are CCM and Nortel M1 pbx. Was working fine until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref = 0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref = 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref = 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
| |
| Ryan Ratliff 2005-12-29, 7:45 am |
| The first call appears to be rejected by your PBX but I think the
debug is missing info. The "Cause i = 0x81B6 - Incoming calls are
barred" should probably appear in a Disconnect or Release message
from the PBX.
The second one is also rejected by the PBX. I would guess because of
the Display IE but the second Release message is a bit confusing.
Is this H.323 or MGCP?
-Ryan
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
Services wrote:
We have a PRI between are CCM and Nortel M1 pbx. Was working fine
until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any
calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right
away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the
Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref =
0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref
= 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8
callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref
= 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Kevin Thorngren 2005-12-29, 7:45 am |
| Are you using DMS-100 Protocol? If so, I believe you need to place a
check mark in the "MCDN Channel Number Extension Bit Set to Zero"
option in the CCM GW configuration.
Let us know if this helps.
Kevin
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
Services wrote:
> We have a PRI between are CCM and Nortel M1 pbx. Was working fine
> until we upgraded.
> We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any calls.
> the D-channel is established.
> but when I try to make a call from my IP phone it disconnects right
> away. when I call from Nortel to IP
> it rings once then disconnects. I did a debug isdn q931 and see the
> Messages.
> Any help is appreciated
>
>
> ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8_ callref =
> 0x0001
> _______ Bearer Capability i = 0x8090A2
> _______________ Standard = CCITT
> _______________ Transer Capability = Speech_
> _______________ Transfer Mode = Circuit
> _______________ Transfer Rate = 64 kbit/s
> _______ Channel ID i = 0xA98381
> _______________ Exclusive, Channel 1
> _______ Display i = 0xB1, 'Gary Sullivan'
> _______ Calling Party Number i = 0x0081, '3102'
> _______________ Plan:Unknown, Type:Unknown
> _______ Called Party Number i = 0x80, '0400'
> _______________ Plan:Unknown, Type:Unknown
>
> 81
> _______ Cause i = 0x81B6 - Incoming calls are barred
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8_ callref =
> 0x17
> _______ Bearer Capability i = 0x8090A2
> _______________ Standard = CCITT
> _______________ Transer Capability = Speech_
> _______________ Transfer Mode = Circuit
> _______________ Transfer Rate = 64 kbit/s
> _______ Channel ID i = 0xE9808317
> _______________ Exclusive, Interface 0, Channel 23
> _______ Display i = 0xB1, 'GARY SULLIVAN'
> _______ Calling Party Number i = 0x0980, '0543'
> _______________ Plan:Private, Type:Unknown
> _______ Called Party Number i = 0x89, '3102'
> _______________ Plan:Private, Type:Unknown
>
>
> _______ Channel ID i = 0xA98397
> _______________ Exclusive, Channel 23
> Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8_
> callref = 0x97
> Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8_ callref
> = 0x97
> _______ Connected Address i = 0x80, '3102'
> _______ Notification Ind i = 0xF1
> _______ Display i = 0xB2, 'Gary Sullivan'
> Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8_ callref
> = 0x17
> _______ Cause i = 0x81E4 - Invalid information element contents
> Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8_ callref
> = 0x17
> _______ Cause i = 0x81E0 - Mandatory information element missing
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Patrick Aland 2005-12-29, 7:45 am |
| try adding
isdn channel-id invert extend-bit
Under your serial interface, i.e.
int ser0/0/0:23
isdn channel-id invert extend-bit
I had the same problem with a Nortel 61C and the above fixed it.
On 12/29/05, Ryan Ratliff <rratliff@cisco.com> wrote:
>
> The first call appears to be rejected by your PBX but I think the
> debug is missing info. The "Cause i = 0x81B6 - Incoming calls are
> barred" should probably appear in a Disconnect or Release message
> from the PBX.
>
> The second one is also rejected by the PBX. I would guess because of
> the Display IE but the second Release message is a bit confusing.
>
> Is this H.323 or MGCP?
>
> -Ryan
>
> On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
> Services wrote:
>
> We have a PRI between are CCM and Nortel M1 pbx. Was working fine
> until we upgraded.
> We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any
> calls. the D-channel is established.
> but when I try to make a call from my IP phone it disconnects right
> away. when I call from Nortel to IP
> it rings once then disconnects. I did a debug isdn q931 and see the
> Messages.
> Any help is appreciated
>
>
> ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref =
> 0x0001
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Display i = 0xB1, 'Gary Sullivan'
> Calling Party Number i = 0x0081, '3102'
> Plan:Unknown, Type:Unknown
> Called Party Number i = 0x80, '0400'
> Plan:Unknown, Type:Unknown
>
> 81
> Cause i = 0x81B6 - Incoming calls are barred
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref
> = 0x17
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xE9808317
> Exclusive, Interface 0, Channel 23
> Display i = 0xB1, 'GARY SULLIVAN'
> Calling Party Number i = 0x0980, '0543'
> Plan:Private, Type:Unknown
> Called Party Number i = 0x89, '3102'
> Plan:Private, Type:Unknown
>
>
> Channel ID i = 0xA98397
> Exclusive, Channel 23
> Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8
> callref = 0x97
> Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref
> = 0x97
> Connected Address i = 0x80, '3102'
> Notification Ind i = 0xF1
> Display i = 0xB2, 'Gary Sullivan'
> Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
> callref = 0x17
> Cause i = 0x81E4 - Invalid information element contents
> Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
> callref = 0x17
> Cause i = 0x81E0 - Mandatory information element missing
>
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
--
--Patrick
| |
| Sullivan, Gary, GREENWICH, 2005-12-29, 5:46 pm |
| MGCP
-----Original Message-----
From: Ryan Ratliff [mailto:rratliff@cisco.com]
Sent: Thursday, December 29, 2005 8:33 AM
To: Sullivan,Gary,GREENWICH,Information Services
Cc: cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] PRI between CCM (3725) and Nortel M1
The first call appears to be rejected by your PBX but I think the
debug is missing info. The "Cause i = 0x81B6 - Incoming calls are
barred" should probably appear in a Disconnect or Release message
from the PBX.
The second one is also rejected by the PBX. I would guess because of
the Display IE but the second Release message is a bit confusing.
Is this H.323 or MGCP?
-Ryan
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
Services wrote:
We have a PRI between are CCM and Nortel M1 pbx. Was working fine
until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any
calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right
away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the
Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref =
0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref
= 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8
callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref
= 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Sullivan, Gary, GREENWICH, 2005-12-29, 5:46 pm |
| When I try to add that I get
GCTRT03(config-if)#isdn channel-id invert extend-bit
^
% Invalid input detected at '^' marker.
The router has is run image c3725-is-mz.122-15.T2.bin
-----Original Message-----
From: Patrick Aland [mailto:paland@gmail.com]
Sent: Thursday, December 29, 2005 8:41 AM
To: Ryan Ratliff
Cc: Sullivan,Gary,GREENWICH,Information Services; cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] PRI between CCM (3725) and Nortel M1
try adding
isdn channel-id invert extend-bit
Under your serial interface, i.e.
int ser0/0/0:23
isdn channel-id invert extend-bit
I had the same problem with a Nortel 61C and the above fixed it.
On 12/29/05, Ryan Ratliff < rratliff@cisco.com> wrote:
The first call appears to be rejected by your PBX but I think the
debug is missing info. The "Cause i = 0x81B6 - Incoming calls are
barred" should probably appear in a Disconnect or Release message
from the PBX.
The second one is also rejected by the PBX. I would guess because of
the Display IE but the second Release message is a bit confusing.
Is this H.323 or MGCP?
-Ryan
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
Services wrote:
We have a PRI between are CCM and Nortel M1 pbx. Was working fine
until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any
calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right
away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the
Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref =
0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref
= 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8
callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref
= 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip <https://puck.nether.net/mailman/listinfo/cisco-voip>
--
--Patrick
| |
| Sullivan, Gary, GREENWICH, 2005-12-29, 5:46 pm |
| Yes using DMS-100 and have that check all ready.
-----Original Message-----
From: Kevin Thorngren [mailto:kthorngr@cisco.com]
Sent: Thursday, December 29, 2005 8:39 AM
To: Sullivan,Gary,GREENWICH,Information Services
Cc: cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] PRI between CCM (3725) and Nortel M1
Are you using DMS-100 Protocol? If so, I believe you need to place a check mark in the "MCDN Channel Number Extension Bit Set to Zero" option in the CCM GW configuration.
Let us know if this helps.
Kevin
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information Services wrote:
We have a PRI between are CCM and Nortel M1 pbx. Was working fine until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref = 0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref = 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref = 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Sullivan, Gary, GREENWICH, 2005-12-29, 5:46 pm |
| I am also on a Nortel 61C rls 25.40
-----Original Message-----
From: Patrick Aland [mailto:paland@gmail.com]
Sent: Thursday, December 29, 2005 8:41 AM
To: Ryan Ratliff
Cc: Sullivan,Gary,GREENWICH,Information Services; cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] PRI between CCM (3725) and Nortel M1
try adding
isdn channel-id invert extend-bit
Under your serial interface, i.e.
int ser0/0/0:23
isdn channel-id invert extend-bit
I had the same problem with a Nortel 61C and the above fixed it.
On 12/29/05, Ryan Ratliff < rratliff@cisco.com> wrote:
The first call appears to be rejected by your PBX but I think the
debug is missing info. The "Cause i = 0x81B6 - Incoming calls are
barred" should probably appear in a Disconnect or Release message
from the PBX.
The second one is also rejected by the PBX. I would guess because of
the Display IE but the second Release message is a bit confusing.
Is this H.323 or MGCP?
-Ryan
On Dec 29, 2005, at 8:13 AM, Sullivan, Gary, GREENWICH, Information
Services wrote:
We have a PRI between are CCM and Nortel M1 pbx. Was working fine
until we upgraded.
We upgraded are CCM from 3.3.4 to 4.1.3 . Now we can't make any
calls. the D-channel is established.
but when I try to make a call from my IP phone it disconnects right
away. when I call from Nortel to IP
it rings once then disconnects. I did a debug isdn q931 and see the
Messages.
Any help is appreciated
ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP pd = 8 callref =
0x0001
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Display i = 0xB1, 'Gary Sullivan'
Calling Party Number i = 0x0081, '3102'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0400'
Plan:Unknown, Type:Unknown
81
Cause i = 0x81B6 - Incoming calls are barred
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
GCTRT03#
Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP pd = 8 callref
= 0x17
Bearer Capability i = 0x8090A2
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808317
Exclusive, Interface 0, Channel 23
Display i = 0xB1, 'GARY SULLIVAN'
Calling Party Number i = 0x0980, '0543'
Plan:Private, Type:Unknown
Called Party Number i = 0x89, '3102'
Plan:Private, Type:Unknown
Channel ID i = 0xA98397
Exclusive, Channel 23
Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX -> ALERTING pd = 8
callref = 0x97
Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX -> NOTIFY pd = 8 callref
= 0x97
Connected Address i = 0x80, '3102'
Notification Ind i = 0xF1
Display i = 0xB2, 'Gary Sullivan'
Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E4 - Invalid information element contents
Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <- RELEASE pd = 8
callref = 0x17
Cause i = 0x81E0 - Mandatory information element missing
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip <https://puck.nether.net/mailman/listinfo/cisco-voip>
--
--Patrick
| |
| Kevin Thorngren 2005-12-29, 5:46 pm |
| Typically this type of behavior is seen when the Extension Bit is set
to 1 but should be set to 0 per DMS-100.
As Ryan stated earlier the Nortel is disconnecting the calls. I'm not
familiar with Nortel gear but are there debugs on the Nortel side you
can look at to see why the calls are being disconnected?
Is it expecting the Extension Bit to be 1 or 0?
The " isdn channel-id invert extended" command was introduced in 12.2
but it doesn't appear it is in the version you are running:
http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/
products_command_reference_chapter09186a
008010b000.html#wp1138159
Kevin
On Dec 29, 2005, at 9:32 AM, Sullivan,Gary,GREENWICH,Information
Services wrote:
[vbcol=seagreen]
> Yes using DMS-100 and have that check all ready.
| |
| Erick Bergquist 2005-12-29, 5:46 pm |
| Also try (if H323), or is it MGCP controlled?
isdn flip-chan-flag
under the D-channel configuration. I had to do that
once when connecting to a Option 61C with cisco router
and DMS 100.
--- "Sullivan, Gary, GREENWICH, Information Services"
<gary.sullivan@waters.nestle.com> wrote:
> Yes using DMS-100 and have that check all ready.
>
> -----Original Message-----
> From: Kevin Thorngren [mailto:kthorngr@cisco.com]
> Sent: Thursday, December 29, 2005 8:39 AM
> To: Sullivan,Gary,GREENWICH,Information Services
> Cc: cisco-voip@puck.nether.net
> Subject: Re: [cisco-voip] PRI between CCM (3725) and
> Nortel M1
>
>
> Are you using DMS-100 Protocol? If so, I believe you
> need to place a check mark in the "MCDN Channel
> Number Extension Bit Set to Zero" option in the CCM
> GW configuration.
>
> Let us know if this helps.
>
> Kevin
> On Dec 29, 2005, at 8:13 AM, Sullivan, Gary,
> GREENWICH, Information Services wrote:
>
>
> We have a PRI between are CCM and Nortel M1 pbx. Was
> working fine until we upgraded.
> We upgraded are CCM from 3.3.4 to 4.1.3 . Now we
> can't make any calls. the D-channel is established.
> but when I try to make a call from my IP phone it
> disconnects right away. when I call from Nortel to
> IP
> it rings once then disconnects. I did a debug isdn
> q931 and see the Messages.
> Any help is appreciated
>
>
> ec 20 09:41:28.853: ISDN Se2/0:23 Q931: TX -> SETUP
> pd = 8 callref = 0x0001
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Display i = 0xB1, 'Gary Sullivan'
> Calling Party Number i = 0x0081, '3102'
> Plan:Unknown, Type:Unknown
> Called Party Number i = 0x80, '0400'
> Plan:Unknown, Type:Unknown
>
> 81
> Cause i = 0x81B6 - Incoming calls are barred
>
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> GCTRT03#
> Dec 20 09:41:38.894: ISDN Se2/0:23 Q931: RX <- SETUP
> pd = 8 callref = 0x17
> Bearer Capability i = 0x8090A2
> Standard = CCITT
> Transer Capability = Speech
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xE9808317
> Exclusive, Interface 0, Channel 23
> Display i = 0xB1, 'GARY SULLIVAN'
> Calling Party Number i = 0x0980, '0543'
> Plan:Private, Type:Unknown
> Called Party Number i = 0x89, '3102'
> Plan:Private, Type:Unknown
>
>
> Channel ID i = 0xA98397
> Exclusive, Channel 23
> Dec 20 09:41:39.206: ISDN Se2/0:23 Q931: TX ->
> ALERTING pd = 8 callref = 0x97
> Dec 20 09:41:39.210: ISDN Se2/0:23 Q931: TX ->
> NOTIFY pd = 8 callref = 0x97
> Connected Address i = 0x80, '3102'
> Notification Ind i = 0xF1
> Display i = 0xB2, 'Gary Sullivan'
> Dec 20 09:41:39.222: ISDN Se2/0:23 Q931: RX <-
> RELEASE pd = 8 callref = 0x17
> Cause i = 0x81E4 - Invalid information
> element contents
> Dec 20 09:41:39.230: ISDN Se2/0:23 Q931: RX <-
> RELEASE pd = 8 callref = 0x17
> Cause i = 0x81E0 - Mandatory information
> element missing
>
__________________________________
Yahoo! for Good - Make a difference this year.
http://brand.yahoo.com/cybergivingweek2005/
|
|
|
|
|