|
Home > Archive > Voice over IP Cisco > September 2005 > 6608 PRI to telco
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
|
|
| Montejano, Ross 2005-09-29, 5:50 pm |
| Hi,
Does anyone have a link to turn up PRI trunks to the telco via a 6608
card, need a quick reference?
TIA
| |
| Lelio Fulgenzi 2005-09-29, 5:50 pm |
| What exactly are you looking for? Here are some starting points:
Device > Gateway > Add a new gateway > cisco Catalyst 6000 T1 VoIP Gateway > Digital Access PRI
and fill in the appropriate parameters.
Your telco will have to answer many of the questions including network time server/client (usually client) and your switch type (DMS-100 mainly in Canada).
Add the mac address of the card from your blade. Do a show port mod to see the MAC addreses.
As far as programming the port itself, here's a typical config statement:
set port voice interface <mod>/<port> dhcp disable <ipaddr> <mask> vlan <vlan> tftp <tftpserverip> gateway <gatewayip>
<------------------------------------ expand window to fit this on one line ------------------------------------------>
Sometimes, you really have to hope and pray to get to configure the port correctly. Sometimes we have had to restart the entire blade to get it working, but usually you have to disable the port first, make the changes, then enable. If it still doesn't work, changing the vlan to an unused VLAN, say 999, then back again helps. We've had conflicting reports that say you have to have ALL your ports registered, whether you use them or not.....balderdash I say - but then again, I'm not CCIE. ;)
You'll also likely see two of these messages with a bit of time between them, don't go on to the next troubleshooting step unless you haven't seen any feed back for about five minutes:
%SYS-4-MODHPRESET:Host process (860) <mod>/<port> got reset asynchronously
--------------------------------------------------------------------------------
Lelio Fulgenzi, B.A.
Network Analyst (CCS) * university of Guelph * Guelph, Ontario N1G 2W1
(519) 824-4120 x56354 (519) 767-1060 FAX (JNHN)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
"I had a coffee and Coke at lunch today...and now, I've got more jitter than an
IP phone on a long haul 10base2 connection" LFJ
----- Original Message -----
From: Montejano, Ross
To: cisco-voip@puck.nether.net
Sent: Thursday, September 29, 2005 11:38 AM
Subject: [cisco-voip] 6608 PRI to telco
Hi,
Does anyone have a link to turn up PRI trunks to the telco via a 6608 card, need a quick reference?
TIA
------------------------------------------------------------------------------
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Hart, Kevin 2005-09-29, 5:50 pm |
| This link might help.
Kevin
http://www.cisco.com/en/US/products..._configuration_
example09186a00801152b9.shtml
_____
From: Montejano, Ross [mailto:rmontejano@enpointe.com]
Sent: Thursday, September 29, 2005 11:38 AM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] 6608 PRI to telco
Hi,
Does anyone have a link to turn up PRI trunks to the telco via a 6608 card,
need a quick reference?
TIA
This message is intended only for the use of the individual or entity to
which it is addressed, and may contain information that is privileged,
confidential, and exempt from disclosure under applicable law. If the reader
of this message is not the intended recipient, or the employee or agent
responsible for delivering the message to the intended recipient, you are
hereby notified that any dissemination, distribution, or copying of this
communication is strictly prohibited. If you have received this
communication in error, please delete it and notify Helix Technology
Corporation immediately.
|
|
|
|
|