|
Home > Archive > Voice over IP Cisco > October 2006 > DPNSS Signaling
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
|
|
|
| I need to integrate a Mitel SX-2000 with a CallManager system via a
point to point T1. They Mitel is currently integrated with another
SX-2000 at the corporate site which will be pulled out to make way for
CallManager. It is my understanding that the Mitel uses DPNSS
signalling to communicate over the T1. I think this may be a problem
for the ISR gateway and CallManager. Is there any way to make these
two talk?
-Adam
| |
| Brian Henry 2006-10-30, 7:12 pm |
| I have seen a Mitel integrated with a 2821 but using QSIG T1 CAS. I will try to get the exact model for you but just incase you need to use DPNSS, then look at the links:
http://www.cisco.com/univercd/cc/td...rv/ac_dpnss.htm
http://www.cisco.com/iamegw/plannin..._components.htm
Brian
________________________________
From: cisco-voip-bounces@puck.nether.net on behalf of Adam
Sent: Mon 10/30/2006 3:44 PM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] DPNSS Signaling
I need to integrate a Mitel SX-2000 with a CallManager system via a
point to point T1. They Mitel is currently integrated with another
SX-2000 at the corporate site which will be pulled out to make way for
CallManager. It is my understanding that the Mitel uses DPNSS
signalling to communicate over the T1. I think this may be a problem
for the ISR gateway and CallManager. Is there any way to make these
two talk?
-Adam
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
| |
| Paul Underwood 2006-10-30, 7:12 pm |
| Adam,
DPNSS is a protocol normally only used by PBXs in the UK and by saying T1
then I assume one end is in the US. Anyway you could use the EGWs but
they’d be expensive and they’ve gone end of life
http://www.cisco.com/en/US/products...0aecd80403827.h
tml
So:-
1. you could stick a QSIG card in the Mitel with a cisco 28XX with the
right vwic, PVDM, IOS etc in MGCP mode on the other end and you’re done
a.
http://www.cisco.com/univercd/cc/td...g/4_1/pbx_int/3
97380mi.pdf <-- old but useful
2. if you still need to use DPNSS and don’t want to fiddle with the
Mitel too much then stick a Westell IQ2000+ box cisco 28XX with the right
vwic, PVDM, IOS etc in MGCP mode on the other end of the link and you’re
done.
a.
http://newsroom.cisco.com/dlls/part..._network_soluti
ons_hospital_073003.pdf <-- It’s been done before by these guys.
3. If you can’t do (2) cause you can’t get the Westell in the US then
you could instead use the Westell IQ2030 attached locally to the Mitel, but
connect to the Westell as a H.323 Gateway over the T1.
Here’s a link explaining the DPNSS features that can be passed between
CallManager and a Westell
http://www.westell.co.uk/support/do...xplainedv41.pdf but
I recommend that you contact Westell or your local cisco office/partner 1st.
Lastly a Westell costs £1000+ and if you go for one I’d recommend that you
have a Mitel engineer one end and a Westell Engineer the other so they can
argue who’s equipment it is that doesn’t work :-)
Rgds,
Paul.
_____
From: cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Brian Henry
Sent: 30 October 2006 21:11
To: Adam; cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] DPNSS Signaling
I have seen a Mitel integrated with a 2821 but using QSIG T1 CAS. I will
try to get the exact model for you but just incase you need to use DPNSS,
then look at the links:
http://www.cisco.com/univercd/cc/td...vdoc/plannirv/a
c_dpnss.htm
http://www.cisco.com/iamegw/plannin..._components.htm
Brian
_____
From: cisco-voip-bounces@puck.nether.net on behalf of Adam
Sent: Mon 10/30/2006 3:44 PM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] DPNSS Signaling
I need to integrate a Mitel SX-2000 with a CallManager system via a
point to point T1. They Mitel is currently integrated with another
SX-2000 at the corporate site which will be pulled out to make way for
CallManager. It is my understanding that the Mitel uses DPNSS
signalling to communicate over the T1. I think this may be a problem
for the ISR gateway and CallManager. Is there any way to make these
two talk?
-Adam
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
|
|
|
|
|