|
Home > Archive > Voice over IP Cisco > July 2006 > Using VWIC-2MFT card with voice and data
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
Using VWIC-2MFT card with voice and data
|
|
| Chris Ellington 2006-07-17, 1:11 pm |
| I know it hasn't been supported to use a 2MFT card with one port T1 data
and the other port PRI but I seem to remember seeing a doc stating that
it was supported.
At present, my TAC engineer thinks I nuts and can't find the doc.
Anyone on the list recall seeing this?
Thanks!
Chris
--
Christopher S. Ellington
CCIE #6814
Network Solutions, Inc.
(317) 566 8897
Chris.Ellington@nsi1.com
| |
| Jason Aarons \(US\) 2006-07-17, 1:11 pm |
| Only issues might be clocking from different sources on the two T1s.
There are clocking limitations on the VWIC2-2MFT-T1/E1. However in
general it does work, I have lots of sites with this configuration.
I would try and stick with a WIC1-DSU if you not sure on the telco
clocking -jason
-----Original Message-----
From: cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Chris Ellington
Sent: Monday, July 17, 2006 10:30 AM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] Using VWIC-2MFT card with voice and data
I know it hasn't been supported to use a 2MFT card with one port T1 data
and the other port PRI but I seem to remember seeing a doc stating that
it was supported.
At present, my TAC engineer thinks I nuts and can't find the doc.
Anyone on the list recall seeing this?
Thanks!
Chris
--
Christopher S. Ellington
CCIE #6814
Network Solutions, Inc.
(317) 566 8897
Chris.Ellington@nsi1.com
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-----------------------------------------
Disclaimer:
This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only. If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful. If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
| |
| ash AD 2006-07-17, 7:12 pm |
| I have always been told no, this could not be done but some documentation says otherwise. Maybe the below URLs is what you are refering to:
http://www.cisco.com/en/US/products...d8028d2e5.shtml
http://www.cisco.com/en/US/products.../>
52c920.shtml
Let us know if you make it work.
Peter Casanave
"Jason Aarons (US)" <jason.aarons@us.didata.com> wrote:
Only issues might be clocking from different sources on the two T1s.
There are clocking limitations on the VWIC2-2MFT-T1/E1. However in
general it does work, I have lots of sites with this configuration.
I would try and stick with a WIC1-DSU if you not sure on the telco
clocking -jason
-----Original Message-----
From: cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Chris Ellington
Sent: Monday, July 17, 2006 10:30 AM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] Using VWIC-2MFT card with voice and data
I know it hasn't been supported to use a 2MFT card with one port T1 data
and the other port PRI but I seem to remember seeing a doc stating that
it was supported.
At present, my TAC engineer thinks I nuts and can't find the doc.
Anyone on the list recall seeing this?
Thanks!
Chris
--
Christopher S. Ellington
CCIE #6814
Network Solutions, Inc.
(317) 566 8897
Chris.Ellington@nsi1.com
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-----------------------------------------
Disclaimer:
This e-mail communication and any attachments may contain
confidential and privileged information and is for use by the
designated addressee(s) named above only. If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful. If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
---------------------------------
See the all-new, redesigned Yahoo.com. Check it out.
| |
| Ted Nugent 2006-07-18, 1:11 am |
| Not if it's supported but it does works. Just make
sure you set your clock source to the voice T1 since
it's less tolerant to slips especially for fax.
Also, you're not crazy.. I've seen that doc as well
but I can't seem to find it again, it might have been
corrected or removed from CCO. It don't believe it was
ISR relevant though which seems to be the problem, at
least it was in my case.
--- Chris Ellington <chris.ellington@nsi1.com> wrote:
> I know it hasn't been supported to use a 2MFT card
> with one port T1 data
> and the other port PRI but I seem to remember seeing
> a doc stating that
> it was supported.
>
> At present, my TAC engineer thinks I nuts and can't
> find the doc.
>
> Anyone on the list recall seeing this?
>
> Thanks!
>
> Chris
>
> --
> Christopher S. Ellington
> CCIE #6814
> Network Solutions, Inc.
> (317) 566 8897
> Chris.Ellington@nsi1.com
>
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
________________________________________
__________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
| |
| Chris Ellington 2006-07-18, 1:11 pm |
| This is the doc I was looking for!
And out of frustration, I tried configuring it last night and it worked _
before, when I would configure a pri-group on the second controller, I got
an error but now it¹s letting me configure it.
So now we can start selling 2 port cards _ one for voice the other for data
rather than two single port cards.
Thanks for all of the help, from the only listserv I subscribe to anymore
due to the excellent signal/noise ratio.
Chris
On 7/17/06 7:48 PM, "ash AD" <commo_ssg_31f@yahoo.com> wrote:
[vbcol=seagreen]
> I have always been told no, this could not be done but some documentationsays
> otherwise. Maybe the below URLs is what you are refering to:
>
>
>
> http://www.cisco.com/en/US/products...900aecd8028d2e5
> .shtml
>
>
>
> http://www.cisco.com/en/US/products...configuration_e
> xample09186a008052c920.shtml
>
>
> Let us know if you make it work.
>
>
>
> Peter Casanave
>
> "Jason Aarons (US)" <jason.aarons@us.didata.com> wrote:
>
--
Christopher S. Ellington
CCIE #6814
Network Solutions, Inc.
(317) 566 8897
Chris.Ellington@nsi1.com
| |
| Wes Sisk 2006-07-19, 1:11 am |
| Be leary. i believe the 2t cards have a limitation that they must
clock against the same TDM clock. If you hook up 2 different clock
sources you will start taking L1 errors.
/Wes
On Jul 18, 2006, at 9:44 AM, Chris Ellington wrote:
This is the doc I was looking for!
And out of frustration, I tried configuring it last night and it
worked – before, when I would configure a pri-group on the second
controller, I got an error but now it’s letting me configure it.
So now we can start selling 2 port cards – one for voice the other
for data rather than two single port cards.
Thanks for all of the help, from the only listserv I subscribe to
anymore due to the excellent signal/noise ratio.
Chris
On 7/17/06 7:48 PM, "ash AD" <commo_ssg_31f@yahoo.com> wrote:
[vbcol=seagreen]
> I have always been told no, this could not be done but some
> documentation says otherwise. Maybe the below URLs is what you are
> refering to:
>
>
>
> http://www.cisco.com/en/US/products/ps5855/
> products_qanda_item0900aecd8028d2e5.shtml
>
>
>
> http://www.cisco.com/en/US/products/hw/modules/ps2617/
> products_configuration_example09186a0080
52c920.shtml
>
>
> Let us know if you make it work.
>
>
>
> Peter Casanave
>
> "Jason Aarons (US)" <jason.aarons@us.didata.com> wrote:
>
--
Christopher S. Ellington
CCIE #6814
Network Solutions, Inc.
(317) 566 8897
Chris.Ellington@nsi1.com
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
|
|
|
|
|