|
Home > Archive > Voice over IP Cisco > March 2007 > fxo port not hanging up
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
fxo port not hanging up
|
|
| Steve G 2007-03-02, 7:11 pm |
| Hello I have an fxo port on a 2851 h323 gateway which is connected to a
Valcom 2003a paging controller. I am having intermittent issues with the
fxo port staying offhook until I shut, no shut it.
here is the config of the voice-port and the dial-peer.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!
voice-port 0/0/0
pre-dial-delay 0
description paging 803[21]
dial-peer voice 803 pots
description Paging at 803[21]
max-conn 1
destination-pattern 803[12]
port 0/0/0
forward-digits 1
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
Does anyone see anything that I might be missing?
Steve
| |
| Jonathan Charles 2007-03-02, 7:11 pm |
| add this to the voice-port:
supervisory disconnect dualtone
http://www.cisco.com/univercd/cc/td...t2/ft_ansds.htm
Jonathan
On 3/2/07, Steve G <smgustafson@gmail.com> wrote:
>
> Hello I have an fxo port on a 2851 h323 gateway which is connected to a
> Valcom 2003a paging controller. I am having intermittent issues with the
> fxo port staying offhook until I shut, no shut it.
>
> here is the config of the voice-port and the dial-peer.
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!
> voice-port 0/0/0
> pre-dial-delay 0
> description paging 803[21]
>
> dial-peer voice 803 pots
> description Paging at 803[21]
> max-conn 1
> destination-pattern 803[12]
> port 0/0/0
> forward-digits 1
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
>
> Does anyone see anything that I might be missing?
>
> Steve
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
| |
| Steve G 2007-03-02, 7:11 pm |
| I configured the 'supervisory disconnect dualtone mid-call' command under
the voice port. I shut no shut the voiceport and waited to see what
happened. It didn't fix the issue. A couple hours later there was another
hung voiceport.
I have not had this problem before with h323. If it were MGCP I could see
the logic, but this is a first for me.
On 3/2/07, Jonathan Charles <jonvoip@gmail.com> wrote:
>
> add this to the voice-port:
>
> supervisory disconnect dualtone
>
>
>
> http://www.cisco.com/univercd/cc/td...t2/ft_ansds.htm
>
>
>
> Jonathan
>
>
> On 3/2/07, Steve G <smgustafson@gmail.com> wrote:
>
>
| |
| Jonathan Charles 2007-03-02, 7:11 pm |
| I am at a loss, usually these are a result of telco not sending the correct
signaling... or your router not listening to it...
Jonathan
On 3/2/07, Steve G <smgustafson@gmail.com> wrote:
>
> I configured the 'supervisory disconnect dualtone mid-call' command under
> the voice port. I shut no shut the voiceport and waited to see what
> happened. It didn't fix the issue. A couple hours later there was another
> hung voiceport.
>
> I have not had this problem before with h323. If it were MGCP I could see
> the logic, but this is a first for me.
>
>
> On 3/2/07, Jonathan Charles <jonvoip@gmail.com> wrote:
>
| |
| Jason Aarons \(US\) 2007-03-03, 7:11 am |
| Did you check with Valcom tech support about your 2003A disconnect
settings. Othan than bad dsps or a debug vpm signal.
From: cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Steve G
Sent: Friday, March 02, 2007 7:39 PM
To: Jonathan Charles
Cc: ciscovoip
Subject:Re: [cisco-voip] fxo port not hanging up
I configured the 'supervisory disconnect dualtone mid-call' command
under the voice port. I shut no shut the voiceport and waited to see
what happened. It didn't fix the issue. A couple hours later there was
another hung voiceport.
I have not had this problem before with h323. If it were MGCP I could
see the logic, but thisis a first for me.
On 3/2/07, Jonathan Charles <jonvoip@gmail.com> wrote:
add this to the voice-port:
supervisory disconnect dualtone
http://www.cisco.com/univercd/cc/td...ios122/122newft
/122t/122t2/ft_ansds.htm
Jonathan
On 3/2/07, Steve G < smgustafson@gmail.com
<mailto:smgustafson@gmail.com> > wrote:
Hello I have an fxo port on a 2851 h323 gateway which is
connected to a Valcom 2003a paging controller. I am having intermittent
issues with the fxo port staying offhook until I shut, no shut it.
here is the config of the voice-port and the dial-peer.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!
voice-port 0/0/0
pre-dial-delay 0
description paging 803[21]
dial-peer voice 803 pots
description Paging at 803[21]
max-conn 1
destination-pattern 803[12]
port 0/0/0
forward-digits 1
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!
Does anyone see anything that I might be missing?
Steve
_______________________________________
________
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
-----------------------------------------
Disclaimer:
This e-mail communication and any attachments maycontain
confidential and privileged information and is for use by the
designated addressee(s) named above only. If you are not the
intended addressee, you are hereby notified that you have received
this communication in error and that any use or reproduction of
this email or its contents is strictly prohibited and may be
unlawful. If you have received this communication in error, please
notify us immediately by replying to this message and deleting it
from your computer. Thank you.
| |
| new look 2007-03-03, 1:11 pm |
| All,
I have the same problem in my IP Phone sys. I have CCM 4.1.3 and theMGCP GW is 2811 and I process a debug vpm signal then
I dailed My company No. then 1 (for AA) then Ext. 160 and hang up before 160 answer it still ringing
got this result
R#debug vpm signal
Voice Port Module signaling debugging is enabled
R#ter mon
R#
R#
*Mar 3 13:11:26.539: htsp_process_event: [1/0/1, FXOLS_ONHOOK, E_DSP_SIG_0000]f
xols_onhook_ringing
*Mar 3 13:11:26.539: htsp_timer - 125 msec
*Mar 3 13:11:26.667:htsp_process_event: [1/0/1, FXOLS_WAIT_RING_MIN, E_HTSP_EV
ENT_TIMER]fxols_wait_ring_min_timer
*Mar 3 13:11:26.667: htsp_timer - 10000 msec
*Mar 3 13:11:27.623: htsp_process_event: [1/0/1, FXOLS_RINGING, E_DSP_SIG_0100]
*Mar 3 13:11:27.623: fxols_ringing_not
*Mar 3 13:11:27.623: htsp_timer_stop
*Mar 3 13:11:27.623: htsp_timer_stop3 htsp_setup_ind
*Mar 3 13:11:27.623: [1/0/1] get_local_station_id calling num= calling name=ca
lling time=03/03 13:11 orig called=
*Mar 3 13:11:27.635: htsp_process_event: [1/0/1, FXOLS_WAIT_SETUP_ACK, E_HTSP_S
ETUP_ACK]
*Mar 3 13:11:27.635: fxols_wait_setup_ack:
*Mar 3 13:11:27.635: [1/0/1] set signal state = 0xC timestamp = 0fxols_check_au
to_call
*Mar 3 13:11:27.639: htsp_process_event: [1/0/1, FXOLS_PROCEEDING, E_HTSP_CONNE
CT]fxols_offhook_connect
*Mar 3 13:11:27.639: htsp_timer_stop
*Mar 3 13:11:27.647: htsp_process_event: [1/0/1, FXOLS_CONNECT, E_HTSP_VOICE_CU
T_THROUGH]fxols_connect_proc_voice
*Mar 3 13:11:27.647: htsp_call_bridged invoked
*Mar 3 13:11:27.659: htsp_process_event: [1/0/1, FXOLS_CONNECT, E_HTSP_VOICE_CU
T_THROUGH]fxols_connect_proc_voice
*Mar 3 13:11:32.091: htsp_digit_ready(1/0/1): digit = 1
*Mar 3 13:11:34.451: htsp_digit_ready(1/0/1): digit = 1
*Mar 3 13:11:34.743: htsp_digit_ready(1/0/1): digit = 6
*Mar 3 13:11:35.143: htsp_digit_ready(1/0/1): digit = 0
*Mar3 13:11:35.451: htsp_digit_ready(1/0/1): digit = #
So can you help please???
----- Original Message ----
From: Jason Aarons (US)<jason.aarons@us.didata.com>
To: Steve G <smgustafson@gmail.com>
Cc: ciscovoip <cisco-voip@puck.nether.net>
Sent: Saturday, March 3, 2007 3:08:27 PM
Subject: Re: [cisco-voip] fxo port not hanging up
Did you check with Valcom tech support about your 2003A disconnect settings. Othan than bad dsps or a debug vpm signal.
From: cisco-voip-bounces@puck.nether.net [mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of Steve G
Sent: Friday, March 02, 2007 7:39 PM
To: Jonathan Charles
Cc: ciscovoip
Subject: Re: [cisco-voip] fxo port not hanging up
I configured the 'supervisory disconnect dualtone mid-call' command under the voice port.. I shut no shut the voiceport and waited to see what happened. It didn'tfix the issue. A couple hours later there was another hung voiceport.
I have not had this problem before with h323. If it were MGCP I could see the logic, but this is a first for me.
On 3/2/07, Jonathan Charles <jonvoip@gmail.com> wrote:
add this to the voice-port:
supervisory disconnect dualtone
http://www.cisco.com/univercd/cc/td...t2/ft_ansds.htm
Jonathan
On 3/2/07, Steve G < smgustafson@gmail.com> wrote:
HelloI have an fxo port on a 2851 h323 gateway which is connected to a Valcom 2003a paging controller. I am having intermittent issues with the fxo port staying offhook until I shut, no shut it.
here is the config of the voice-port and the dial-peer.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!
voice-port 0/0/0
pre-dial-delay 0
description paging 803[21]
dial-peer voice 803 pots
description Paging at 803[21]
max-conn 1
destination-pattern 803[12]
port 0/0/0
forward-digits 1
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
Does anyone see anything that I might be missing?
Steve
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
Disclaimer: This e-mail communication and any attachments may contain confidential and privileged information and is for use by the designated addressee(s) named above only. If you are not the intended addressee, youare hereby notified that you have received this communication in error andthat any use or reproduction of this email or its contents is strictly prohibited and may be unlawful. If you have received this communication in error, please notify us immediately by replying to this message and deleting it from your computer. Thank you.
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
________________________________________
________________________________________
____
It's here! Your new message!
Get new email alerts with the free Yahoo! Toolbar.
http://tools.search.yahoo.com/toolbar/features/mail/
| |
| Steve G 2007-03-03, 7:11 pm |
| I think I found the problem. Well, the router was running IOS 12.4(3)g, and
I upgraded to 12.4(8)c as per my company standard and found that I have gone
the whole day without a hung fxo port. I will continue to monitor but I'm
convinced that upgrading the IOS was the trick.
On 3/3/07, Jason Aarons (US) <jason.aarons@us.didata.com> wrote:
>
> Did you check with Valcom tech support about your 2003A disconnect
> settings. Othan than bad dsps or a debug vpm signal.
>
>
>
> *From:* cisco-voip-bounces@puck.nether.net [mailto:
> cisco-voip-bounces@puck.nether.net] *On Behalf Of *Steve G
> *Sent:* Friday, March 02, 2007 7:39 PM
> *To:* Jonathan Charles
> *Cc:* ciscovoip
> *Subject:* Re: [cisco-voip] fxo port not hanging up
>
>
>
> I configured the 'supervisory disconnect dualtone mid-call' command under
> the voice port. I shut no shut the voiceport and waited to see what
> happened. It didn't fix the issue. A couple hours later there was another
> hung voiceport.
>
>
>
> I have not had this problem before with h323. If it were MGCP I could see
> the logic, but this is a first for me.
>
>
>
> On 3/2/07, *Jonathan Charles* <jonvoip@gmail.com> wrote:
>
> add this to the voice-port:
>
>
>
> supervisory disconnect dualtone
>
>
>
>
>
> http://www.cisco.com/univercd/cc/td...t2/ft_ansds.htm
>
>
>
>
>
>
>
>
> Jonathan
>
>
>
> On 3/2/07, *Steve G* < smgustafson@gmail.com> wrote:
>
> Hello I have an fxo port on a 2851 h323 gateway which is connected to a
> Valcom 2003a paging controller. I am having intermittent issues with the
> fxo port staying offhook until I shut, no shut it.
>
>
>
> here is the config of the voice-port and the dial-peer.
>
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!
>
> voice-port 0/0/0
> pre-dial-delay 0
> description paging 803[21]
>
>
>
> dial-peer voice 803 pots
> description Paging at 803[21]
> max-conn 1
> destination-pattern 803[12]
> port 0/0/0
> forward-digits 1
>
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
>
>
>
> Does anyone see anything that I might be missing?
>
>
>
> Steve
>
>
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
>
>
>
> ------------------------------
>
> *Disclaimer: This e-mail communication and any attachments may contain
> confidential and privileged information and is for use by the designated
> addressee(s) named above only. If you are not the intended addressee, you
> are hereby notified that you have received this communication in error and
> that any use or reproduction of this email or its contents is strictly
> prohibited and may be unlawful. If you have received this communication in
> error, please notify us immediately by replying to this message and deleting
> it from your computer. Thank you. *
>
|
|
|
|
|