|
Home > Archive > Voice over IP Cisco > March 2007 > CCM & PBX via Qsig
You are viewing an archived Text-only version of the thread.
To view this thread in it's original format and/or if you want to reply to
this thread please [click here]
| Author |
CCM & PBX via Qsig
|
|
|
| Hi,
I have the following setup:
A Siemens PBX connecting to a CallManager via Qsig (mgcp controlled)
and
the CCM connecting to PSTN via PRI (mgcp controlled)
Calls to and from CCM works fine (inbound and outbound)
Calls to and from PBX works fine (inbound and outbound)
Calls from CCM to PBX works fine
Calls from PBX to CCM does not work
My D-channel towards the PBX looks like this:
!
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn overlap-receiving T302 2000
isdn incoming-voice voice
isdn bind-l3 ccm-manager
isdn sending-complete
no cdp enable
end
!
and debug isdn q931 gives the following:
01260: Mar 25 11:13:42.699 SAST: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8
callref = 0x0001
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Facility i =
0x91AA068001008201008B0100A10D02017D0604
2B0C092903020780
Facility i =
0x91AA068001008201008B0102A11302017E0201
3B300B30090A01050A01040A0103
Facility i =
0x91AA068001008201008B0100A11402017F0604
2B0C09008009524543455054494F4E
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0183, '70008'
Plan:ISDN, Type:Unknown
Called Party Number i = 0x89, '70051'
Plan:Private, Type:Unknown
Locking Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
001261: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd =
8 callref = 0x8001
Channel ID i = 0xA98381
Exclusive, Channel 1
001262: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> FACILITY pd = 8
callref = 0x8001
Facility i = 0x9FAA06800100820100A40602017E800100
001263: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8
callref = 0x8001
Facility i =
0x9FAA06800100820100A112020101020101800A
4D6172636F204465656E
Progress Ind i = 0x8088 - In-band info or appropriate now available
001264: Mar 25 11:13:42.759 SAST: ISDN Se1/0:15 Q931: RX <- STATUS pd = 8
callref = 0x0001
Cause i = 0x81E41C - Invalid information element contents
Call State i = 0x03
001265: Mar 25 11:13:42.771 SAST: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd =
8 callref = 0x8001
Cause i = 0x80E2 - Message not compatible with call state or not
implemented
001266: Mar 25 11:13:43.075 SAST: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8
callref = 0x0001
001267: Mar 25 11:13:43.099 SAST: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd
= 8 callref = 0x8001
Any ideas? Where to look?
Thnx
Charl
| |
| Aman Chugh 2007-03-25, 7:11 am |
| On Mgcp gw page in cm , try changing display IE and facility IE settings ,
that is try un checking them and reset the gw and then test the call and try
to capture the debug as well.
If I understand correctly calls from Siemens to cm dont work.
On 3/25/07, Lemon <lemon@lemon.za.net> wrote:
>
> Hi,
>
> I have the following setup:
>
> A Siemens PBX connecting to a CallManager via Qsig (mgcp controlled)
>
> and
>
> the CCM connecting to PSTN via PRI (mgcp controlled)
>
> Calls to and from CCM works fine (inbound and outbound)
> Calls to and from PBX works fine (inbound and outbound)
> Calls from CCM to PBX works fine
> Calls from PBX to CCM does not work
>
> My D-channel towards the PBX looks like this:
> !
> interface Serial1/0:15
> no ip address
> encapsulation hdlc
> isdn switch-type primary-qsig
> isdn overlap-receiving T302 2000
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> isdn sending-complete
> no cdp enable
> end
> !
>
> and debug isdn q931 gives the following:
>
> 01260: Mar 25 11:13:42.699 SAST: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8
> callref = 0x0001
> Sending Complete
> Bearer Capability i = 0x9090A3
> Standard = CCITT
> Transfer Capability = 3.1kHz Audio
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Facility i =
> 0x91AA068001008201008B0100A10D02017D0604
2B0C092903020780
> Facility i =
> 0x91AA068001008201008B0102A11302017E0201
3B300B30090A01050A01040A0103
> Facility i =
> 0x91AA068001008201008B0100A11402017F0604
2B0C09008009524543455054494F4E
> Progress Ind i = 0x8183 - Origination address is non-ISDN
> Calling Party Number i = 0x0183, '70008'
> Plan:ISDN, Type:Unknown
> Called Party Number i = 0x89, '70051'
> Plan:Private, Type:Unknown
> Locking Shift to Codeset 5
> Codeset 5 IE 0x32 i = 0x81
> 001261: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd =
> 8 callref = 0x8001
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> 001262: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> FACILITY pd =
> 8 callref = 0x8001
> Facility i = 0x9FAA06800100820100A40602017E800100
> 001263: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> ALERTING pd =
> 8 callref = 0x8001
> Facility i =
> 0x9FAA06800100820100A112020101020101800A
4D6172636F204465656E
> Progress Ind i = 0x8088 - In-band info or appropriate now
> available
> 001264: Mar 25 11:13:42.759 SAST: ISDN Se1/0:15 Q931: RX <- STATUS pd = 8
> callref = 0x0001
> Cause i = 0x81E41C - Invalid information element contents
> Call State i = 0x03
> 001265: Mar 25 11:13:42.771 SAST: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd
> = 8 callref = 0x8001
> Cause i = 0x80E2 - Message not compatible with call state or not
> implemented
> 001266: Mar 25 11:13:43.075 SAST: ISDN Se1/0:15 Q931: RX <- RELEASE pd =
> 8 callref = 0x0001
> 001267: Mar 25 11:13:43.099 SAST: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP
> pd = 8 callref = 0x8001
>
>
>
> Any ideas? Where to look?
>
> Thnx
>
> Charl
>
> ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
>
>
| |
| Dietmar 2007-03-25, 1:11 pm |
| Hi,
have you set the "Channel IE Type" to "Continuous Number" on the gateway
configuration site? The protocol on the Siemens should be set to PSS1V2.
Dietmar
On Sunday 25 March 2007 12:48:28 Lemon wrote:
> Hi,
>
> I have the following setup:
>
> A Siemens PBX connecting to a CallManager via Qsig (mgcp controlled)
>
> and
>
> the CCM connecting to PSTN via PRI (mgcp controlled)
>
> Calls to and from CCM works fine (inbound and outbound)
> Calls to and from PBX works fine (inbound and outbound)
> Calls from CCM to PBX works fine
> Calls from PBX to CCM does not work
>
> My D-channel towards the PBX looks like this:
> !
> interface Serial1/0:15
> no ip address
> encapsulation hdlc
> isdn switch-type primary-qsig
> isdn overlap-receiving T302 2000
> isdn incoming-voice voice
> isdn bind-l3 ccm-manager
> isdn sending-complete
> no cdp enable
> end
> !
>
> and debug isdn q931 gives the following:
>
> 01260: Mar 25 11:13:42.699 SAST: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8
> callref = 0x0001
> Sending Complete
> Bearer Capability i = 0x9090A3
> Standard = CCITT
> Transfer Capability = 3.1kHz Audio
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> Facility i =
> 0x91AA068001008201008B0100A10D02017D0604
2B0C092903020780
> Facility i =
> 0x91AA068001008201008B0102A11302017E0201
3B300B30090A01050A01040A0103
> Facility i =
> 0x91AA068001008201008B0100A11402017F0604
2B0C09008009524543455054494F4E
> Progress Ind i = 0x8183 - Origination address is non-ISDN
> Calling Party Number i = 0x0183, '70008'
> Plan:ISDN, Type:Unknown
> Called Party Number i = 0x89, '70051'
> Plan:Private, Type:Unknown
> Locking Shift to Codeset 5
> Codeset 5 IE 0x32 i = 0x81
> 001261: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd =
> 8 callref = 0x8001
> Channel ID i = 0xA98381
> Exclusive, Channel 1
> 001262: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> FACILITY pd = 8
> callref = 0x8001
> Facility i = 0x9FAA06800100820100A40602017E800100
> 001263: Mar 25 11:13:42.727 SAST: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8
> callref = 0x8001
> Facility i =
> 0x9FAA06800100820100A112020101020101800A
4D6172636F204465656E
> Progress Ind i = 0x8088 - In-band info or appropriate now available
> 001264: Mar 25 11:13:42.759 SAST: ISDN Se1/0:15 Q931: RX <- STATUS pd = 8
> callref = 0x0001
> Cause i = 0x81E41C - Invalid information element contents
> Call State i = 0x03
> 001265: Mar 25 11:13:42.771 SAST: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd =
> 8 callref = 0x8001
> Cause i = 0x80E2 - Message not compatible with call state or not
> implemented
> 001266: Mar 25 11:13:43.075 SAST: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8
> callref = 0x0001
> 001267: Mar 25 11:13:43.099 SAST: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd
> = 8 callref = 0x8001
>
>
>
> Any ideas? Where to look?
>
> Thnx
>
> Charl
--
E-Mail: db7td@gmx.de
| |
|
| HI
On 3/25/07, Dietmar <db7td@gmx.de> wrote:
>
> Hi,
>
> have you set the "Channel IE Type" to "Continuous Number" on the gateway
> configuration site? The protocol on the Siemens should be set to PSS1V2.
Yup, have done this - like I said calls from PBX to PSTN via MGCP
controlled PRI does work. Only internal calls from PBX to CCM does not work
Thnx
Charl
|
|
|
|
|