|
|
| Woggle 2006-08-13, 1:11 pm |
| I'm trying to set the SPA 3000 so I can call in from my mobile number
and then receive a dial tone and dial out through Voip.
Unfortunately the SPA doesn't recognise my mobile number. If I leave
both PSTN Caller ID Pattern and PSTN Access List blank then it works
for any number but I want to restrict this just to my mobile.
Settings are as follows:
PSTN-To-Voip Gateway Setup: Yes
PSTN Caller Auth Method: Yes
PSTN Ring Thru Line 1: Yes
PSTN PIN Max Retry:
PSTN CID for Voip CID: Yes
PSTN CID Number Prefix:
PSTN Caller Default DP: 1
Off Hook while calling Voip: No
Line 1 signal hook flash to PSTN: Disabled
PSTN CID Name Prefix:
PSTN Caller ID Patter: (just enter my mobile number starting 07)
PSTN Access List: (just enter my mobile number starting 07)
PSTN Caller 1 PIN: 1234
PSTN Caller DP: 1
PSTN Answer Delay: 5
PSTN PIN Digit Timeout: 10
As for CID - I'm currently in the UK and it is set to (under Regional
Tab) ETSI FSK with PR (UK)
Caller ID FSK Standard is set to bell 2002
On info page, last PSTN caller comes up as , 07 (i.e. my mobile number)
Thanks
| |
|
|
"Woggle" <markgolledge@googlemail.com> wrote in message
news:1155472558.114346.286980@i3g2000cwc.googlegroups.com...
> I'm trying to set the SPA 3000 so I can call in from my mobile number
> and then receive a dial tone and dial out through Voip.
>
> Unfortunately the SPA doesn't recognise my mobile number. If I leave
> both PSTN Caller ID Pattern and PSTN Access List blank then it works
> for any number but I want to restrict this just to my mobile.
>
> Settings are as follows:
>
> PSTN-To-Voip Gateway Setup: Yes
> PSTN Caller Auth Method: Yes
> PSTN Ring Thru Line 1: Yes
> PSTN PIN Max Retry:
> PSTN CID for Voip CID: Yes
> PSTN CID Number Prefix:
> PSTN Caller Default DP: 1
> Off Hook while calling Voip: No
> Line 1 signal hook flash to PSTN: Disabled
> PSTN CID Name Prefix:
> PSTN Caller ID Patter: (just enter my mobile number starting 07)
> PSTN Access List: (just enter my mobile number starting 07)
> PSTN Caller 1 PIN: 1234
> PSTN Caller DP: 1
>
> PSTN Answer Delay: 5
> PSTN PIN Digit Timeout: 10
>
> As for CID - I'm currently in the UK and it is set to (under Regional
> Tab) ETSI FSK with PR (UK)
>
> Caller ID FSK Standard is set to bell 2002
>
>
> On info page, last PSTN caller comes up as , 07 (i.e. my mobile number)
>
>
>
> Thanks
What firmware are you using?
From their FAQ: "NOTE: SPA-3000 only supports Bellcore Type I (On-Hook)
Caller ID." (which may only refer to the Access List & Pattern list)
http://www.sipura.com/support/spa30...ection_4.html#1
AFAIR, I had exactly the problem you describe & came to the conclusion that
it doesn't function on UK callerID
| |
| Woggle 2006-08-14, 1:11 pm |
| Thanks for the note -
I'm using Firmware software version 3.1.10 (Gwd) and hardware version
2.0.1(9472)
So are you saying this doesn't work with UK Caller ID or is it that I
need to change -
PSTN Answer Delay to something like 16
and
PSTN Ring Thru Delay to something like 5
so the SPA recognises Caller ID??
(although that is based on US numbers).
If it will never recognise it, I guess the only way around it then
would be to leave it blank so that everyone gets the Voip line.
That is quite annoying given that I would want the answerphone to pick
up any messages and it wouldn't be able to under this way.
Mark
Jono wrote:
> "Woggle" <markgolledge@googlemail.com> wrote in message
> news:1155472558.114346.286980@i3g2000cwc.googlegroups.com...
>
> What firmware are you using?
>
> From their FAQ: "NOTE: SPA-3000 only supports Bellcore Type I (On-Hook)
> Caller ID." (which may only refer to the Access List & Pattern list)
> http://www.sipura.com/support/spa30...ection_4.html#1
>
> AFAIR, I had exactly the problem you describe & came to the conclusion that
> it doesn't function on UK callerID
| |
|
| Woggle pretended :[vbcol=seagreen]
> Thanks for the note -
>
> I'm using Firmware software version 3.1.10 (Gwd) and hardware version
> 2.0.1(9472)
>
> So are you saying this doesn't work with UK Caller ID or is it that I
> need to change -
>
> PSTN Answer Delay to something like 16
>
> and
>
> PSTN Ring Thru Delay to something like 5
>
> so the SPA recognises Caller ID??
>
> (although that is based on US numbers).
>
> If it will never recognise it, I guess the only way around it then
> would be to leave it blank so that everyone gets the Voip line.
>
> That is quite annoying given that I would want the answerphone to pick
> up any messages and it wouldn't be able to under this way.
>
> Mark
>
>
>
> Jono wrote:
I'm saying........"I could never get it to work"
I will be watching this thread in the hope that someone else /has/ got
it to work.
| |
|
| Woggle, setup an account with http://www.voipfone.co.uk slap some
credit on and they have a geo number you can dial with your mobile to
get a dialtone so you can make calls thru voip. Works well too.
---
External Post from http://ukvoiptalk.com
| |
| thomas.lewandowski@gmail.com 2006-08-22, 7:11 pm |
| Woggle wrote:
> I'm trying to set the SPA 3000 so I can call in from my mobile number
> and then receive a dial tone and dial out through Voip.
>
> Unfortunately the SPA doesn't recognise my mobile number. If I leave
try (on PSTN Line) Ring Validation Time=150ms, Ring Indication Delay=0
> PSTN Caller ID Patter: (just enter my mobile number starting 07)
> PSTN Access List: (just enter my mobile number starting 07)
generally, if you want to use pin authentification, it's not good idea
to write in both fields the same number, from sipuras manual:
"PSTN Access List - A comma separated list of caller number templates
such that PSTN callers with numbers matching any of these templates
will be accepted for VoIP gateway service without authentication."
Leave in "PSTN Caller ID Pattern" your number and remove all data from
"PSTN Access List", don't forget also your number in "Cfwd Sel1 Caller"
(PSTN User)
|
|
|
|