05-26-05 10:49 PM
ny-1700-5#cd html
%Error statting flash:/html (No such file or directory)
Just as I suspected, can't CD to a non-existant directory...and mkdir
doesn't help since it doesn't exist on my router...
-Anthony
> -----Original Message-----
> From: *VoIP Help [mailto:voiphelp@apptis.com]
> Sent: Thursday, May 26, 2005 6:18 AM
> To: Anthony Mendoza; cisco-voip@puck.nether.net
> Subject: RE: [cisco-voip] Stupid Question - how to make
> directory on flashfilesystem with IOS
>
> Try cd to the dir and then mkdir
>
> -----Original Message-----
> From: cisco-voip-bounces@puck.nether.net
> [mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of
> Anthony Mendoza
> Sent: Thursday, May 26, 2005 1:10 AM
> To: cisco-voip@puck.nether.net
> Subject: [cisco-voip] Stupid Question - how to make directory on
> flashfilesystem with IOS
>
> I'm running:
>
> ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
>
> ny-1700-5 uptime is 53 minutes
> System returned to ROM by reload at 00:11:57 EDT Thu May 26 2005
> System restarted at 00:15:00 EDT Thu May 26 2005
> System image file is "flash:c1700-sv8y7-mz.123-4.T6.bin"
>
> and am preparing this box for a CME install..
>
> I want to put the GUI files in /html off the flash, however, I can't
> seem to find the command to make a directory..I thought it was mkdir,
> but from ? output below you can see it isn't listed...am I crazy or is
> there no way to create a directory on the load I'm at?
>
> ny-1700-5#?
> Exec commands:
> <1-99> Session number to resume
> access-enable Create a temporary Access-List entry
> access-profile Apply user-profile to interface
> access-template Create a temporary Access-List entry
> archive manage archive files
> audio-prompt load ivr prompt
> auto Exec level Automation
> bfe For manual emergency modes setting
> call Reload IVR call application, accounting template
> ccm-manager Call Manager Application exec commands
> cd Change current directory
> clear Reset functions
> clock Manage the system clock
> cns CNS agents
> configure Enter configuration mode
> connect Open a terminal connection
> copy Copy from one file to another
> debug Debugging functions (see also 'undebug')
> delete Delete a file
> dir List files on a filesystem
> disable Turn off privileged commands
> disconnect Disconnect an existing network connection
> enable Turn on privileged commands
> erase Erase a filesystem
> exit Exit from the EXEC
> help Description of the interactive help system
> isdn Run an ISDN EXEC command on an ISDN interface
> lock Lock the terminal
> login Log in as a particular user
> logout Exit from the EXEC
> modemui Start a modem-like user interface
> monitor Monitoring different system events
> more Display the contents of a file
> mrinfo Request neighbor and version information from a
> multicast
> router
> mrm IP Multicast Routing Monitor Test
> mstat Show statistics after multiple multicast
> traceroutes
> mtrace Trace reverse multicast path from destination to
> source
> name-connection Name an existing network connection
> no Disable debugging functions
> pad Open a X.29 PAD connection
> ping Send echo messages
> ppp Start IETF Point-to-Point Protocol (PPP)
> pwd Display current working directory
> release Release a resource
> reload Halt and perform a cold restart
> rename Rename a file
> renew Renew a resource
> restart Restart Connection
> resume Resume an active network connection
> rlogin Open an rlogin connection
> rsh Execute a remote command
> send Send a message to other tty lines
> setup Run the SETUP command facility
> show Show running system information
> slip Start Serial-line IP (SLIP)
> squeeze Squeeze a filesystem
> start-chat Start a chat-script on a line
> systat Display information about terminal lines
> tclquit Quit Tool Command Language shell
> tclsh Tool Command Language shell
> telnet Open a telnet connection
> terminal Set terminal line parameters
> test Test subsystems, memory, and interfaces
> traceroute Trace route to destination
> tunnel Open a tunnel connection
> udptn Open an udptn connection
> undebug Disable debugging functions (see also 'debug')
> verify Verify a file
> voice Voice Commands
> where List active connections
> write Write running configuration to memory, network, or
> terminal
> x28 Become an X.28 PAD
> x3 Set X.3 parameters on PAD
>
> --
> Anthony Mendoza
>
>
> CONFIDENTIALITY NOTICE: The information contained in this message and
> or attachments is intended only for the person or entity to
> which it is
> addressed and may contain confidential and/or privileged material. Any
> review, retransmission, dissemination, copying, or other use of this
> information by persons or entities other than the intended
> recipient is
> prohibited. If you received this e-mail or its attachments in error,
> please contact the sender and delete the material from any system and
> destroy any copies.
>
>
CONFIDENTIALITY NOTICE: The information contained in this message and
or attachments is intended only for the person or entity to which it is
addressed and may contain confidential and/or privileged material. Any
review, retransmission, dissemination, copying, or other use of this
information by persons or entities other than the intended recipient is
prohibited. If you received this e-mail or its attachments in error,
please contact the sender and delete the material from any system and
destroy any copies.
[ Post a follow-up to this message ]
| 
