On my gw im trying to config the line code and framing    with ser- mod
XXXX

But they wont show up under the serial int.  Im trying a add the cmd under
the serial interface.  Because this is not a VWIC card.  Can someone tell me
what am I missing



James D. Grace

CCNP CCNA MCSE MCDBA

Sr. System Engineer / Professional Svc.

Digitel Corporation

Attachment:
This has been downloaded 0 time(s).

[ Post a follow-up to this message ]

Interface configuration

 

Service-module t1 <framing> or <linecode> 

 

In newer IOS is doesn't show up in the config.

 

 

 

________________________________

From: cisco-voip-bounces@puck.nether.net
[mailto:cisco-voip-bounces@puck.nether.net] On Behalf Of James Grace
Sent: Wednesday, December 28, 2005 10:39 AM
To: cisco-voip@puck.nether.net
Subject: [cisco-voip] config p2p on my voice gw

 

On my gw im trying to config the line code and framing    with ser- mod
XXXX

But they wont show up under the serial int.  Im trying a add the cmd
under the serial interface.  Because this is not a VWIC card.  Can
someone tell me what am I missing 

 

James D. Grace 

CCNP CCNA MCSE MCDBA

Sr. System Engineer / Professional Svc.

Digitel Corporation

 

Attachment:
This has been downloaded 0 time(s).

[ Post a follow-up to this message ]

Still not sure what type of card you have.  Try using "show inventory"  
to get the part number.  If you have WIC-1DSU-T1 then take a look at  
this web page and use the service-module command:
http://www.cisco.com/en/US/products/hw/modules/ps3129/ 
products_tech_note09186a00800b1501.shtml

If you have something like the WIC-2T or WIC-1T then you will need an  
external CSU/DSU and a V.35 cable.  You will then configure the CSU/DSU  
with the Line Coding and Framing.
http://www.cisco.com/en/US/products/hw/routers/ps274/ 
products_tech_note09186a00800b0858.shtml

HTH,
Kevin

On Dec 28, 2005, at 1:38 PM, James Grace wrote:

> On my gw im trying to config the line code and framing___ with ser-  
> mod_ XXXX
> But they wont show up under the serial int._ Im trying a add the cmd  
> under the serial interface._ Because this is not a VWIC card._ Can  
> someone tell me what am I missing
> _
> James D. Grace
> CCNP CCNA MCSE MCDBA
> Sr. System Engineer / Professional Svc.
> Digitel Corporation
> _
>  ________________________________________
_______
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip

Attachment:
This has been downloaded 0 time(s).

[ Post a follow-up to this message ]

The commands won't show up in the config if the
default options are used which is probably the case if
you're in the US and are using all 24 channels. =


A 'show service-module' will tell you details on how
it is currently running and give framing, lining,
clocking, clock speed, errors if any, alarms if any,
etc. =


--- Kevin Thorngren <kthorngr@cisco.com> wrote:

> Still not sure what type of card you have.  Try
> using "show inventory"  =

> to get the part number.  If you have WIC-1DSU-T1
> then take a look at  =

> this web page and use the service-module command:
>
http://www.cisco.com/en/US/products/hw/modules/ps3129/
> =

> products_tech_note09186a00800b1501.shtml
> =

> If you have something like the WIC-2T or WIC-1T then
> you will need an  =

> external CSU/DSU and a V.35 cable.  You will then
> configure the CSU/DSU  =

> with the Line Coding and Framing.
>
http://www.cisco.com/en/US/products/hw/routers/ps274/
> =

> products_tech_note09186a00800b0858.shtml
> =

> HTH,
> Kevin
> =

> On Dec 28, 2005, at 1:38 PM, James Grace wrote:
> =
 
> framing=EF=BF=BD=EF=BF=BD=EF=BF=BD with ser-  =
 
> trying a add the cmd  =
 
a[vbcol=seagreen]
> VWIC card.=EF=BF=BD Can  =
 
> https://puck.nether.net/mailman/listinfo/cisco-voip 
> cisco-voip mailing list
> cisco-voip@puck.nether.net
> https://puck.nether.net/mailman/listinfo/cisco-voip
> =




=

 ________________________________________
__ =

Yahoo! DSL =96 Something to write home about. =

Just $16.99/mo. or less. =

dsl.yahoo.com =

[ Post a follow-up to this message ]