03-03-07 06:11 PM
All,
I have the same problem in my IP Phone sys. I have CCM 4.1.3 and theMGCP GW
is 2811 and I process a debug vpm signal then
I dailed My company No. then 1 (for AA) then Ext. 160 and hang up before 160
answer it still ringing
got this result
R#debug vpm signal
Voice Port Module signaling debugging is enabled
R#ter mon
R#
R#
*Mar 3 13:11:26.539: htsp_process_event: [1/0/1, FXOLS_ONHOOK, E_DSP_SI
G_0000]f
xols_onhook_ringing
*Mar 3 13:11:26.539: htsp_timer - 125 msec
*Mar 3 13:11:26.667:htsp_process_event: [1/0/1, FXOLS_WAIT_RING_MIN, E_
HTSP_EV
ENT_TIMER]fxols_wait_ring_min_timer
*Mar 3 13:11:26.667: htsp_timer - 10000 msec
*Mar 3 13:11:27.623: htsp_process_event: [1/0/1, FXOLS_RINGING, E_DSP_S
IG_0100]
*Mar 3 13:11:27.623: fxols_ringing_not
*Mar 3 13:11:27.623: htsp_timer_stop
*Mar 3 13:11:27.623: htsp_timer_stop3 htsp_setup_ind
*Mar 3 13:11:27.623: [1/0/1] get_local_station_id calling num= calling
name=ca
lling time=03/03 13:11 orig called=
*Mar 3 13:11:27.635: htsp_process_event: [1/0/1, FXOLS_WAIT_SETUP_ACK,
E_HTSP_S
ETUP_ACK]
*Mar 3 13:11:27.635: fxols_wait_setup_ack:
*Mar 3 13:11:27.635: [1/0/1] set signal state = 0xC timestamp = 0fxols_
check_au
to_call
*Mar 3 13:11:27.639: htsp_process_event: [1/0/1, FXOLS_PROCEEDING, E_HT
SP_CONNE
CT]fxols_offhook_connect
*Mar 3 13:11:27.639: htsp_timer_stop
*Mar 3 13:11:27.647: htsp_process_event: [1/0/1, FXOLS_CONNECT, E_HTSP_
VOICE_CU
T_THROUGH]fxols_connect_proc_voice
*Mar 3 13:11:27.647: htsp_call_bridged invoked
*Mar 3 13:11:27.659: htsp_process_event: [1/0/1, FXOLS_CONNECT, E_HTSP_
VOICE_CU
T_THROUGH]fxols_connect_proc_voice
*Mar 3 13:11:32.091: htsp_digit_ready(1/0/1): digit = 1
*Mar 3 13:11:34.451: htsp_digit_ready(1/0/1): digit = 1
*Mar 3 13:11:34.743: htsp_digit_ready(1/0/1): digit = 6
*Mar 3 13:11:35.143: htsp_digit_ready(1/0/1): digit = 0
*Mar3 13:11:35.451: htsp_digit_ready(1/0/1): digit = #
So can you help please???
----- Original Message ----
From: Jason Aarons (US)<jason.aarons@us.didata.com>
To: Steve G <smgustafson@gmail.com>
Cc: ciscovoip <cisco-voip@puck.nether.net>
Sent: Saturday, March 3, 2007 3:08:27 PM
Subject: Re: [cisco-voip] fxo port not hanging up
Did you check with Valcom tech support about your 2003A disconnect settings.
Othan than bad dsps or a debug vpm signal.
From: cisco-voip-bounces@puck.nether.net [mailto:cisco-voip-bounces@puck
.nether.net] On Behalf Of Steve G
Sent: Friday, March 02, 2007 7:39 PM
To: Jonathan Charles
Cc: ciscovoip
Subject: Re: [cisco-voip] fxo port not hanging up
I configured the 'supervisory disconnect dualtone mid-call' command under th
e voice port.. I shut no shut the voiceport and waited to see what happened
. It didn'tfix the issue. A couple hours later there was another hung voic
eport.
I have not had this problem before with h323. If it were MGCP I could see t
he logic, but this is a first for me.
On 3/2/07, Jonathan Charles <jonvoip@gmail.com> wrote:
add this to the voice-port:
supervisory disconnect dualtone
http://www.cisco.com/univercd/cc/td...
2/ft_ansds.htm
Jonathan
On 3/2/07, Steve G < smgustafson@gmail.com> wrote:
HelloI have an fxo port on a 2851 h323 gateway which is connected to a Valco
m 2003a paging controller. I am having intermittent issues with the fxo por
t staying offhook until I shut, no shut it.
here is the config of the voice-port and the dial-peer.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!
voice-port 0/0/0
pre-dial-delay 0
description paging 803[21]
dial-peer voice 803 pots
description Paging at 803[21]
max-conn 1
destination-pattern 803[12]
port 0/0/0
forward-digits 1
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!
Does anyone see anything that I might be missing?
Steve
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
Disclaimer: This e-mail communication and any attachments may contain confid
ential and privileged information and is for use by the designated addressee
(s) named above only. If you are not the intended addressee, youare hereby n
otified that you have received this communication in error andthat any use o
r reproduction of this email or its contents is strictly prohibited and may
be unlawful. If you have received this communication in error, please notify
us immediately by replying to this message and deleting it from your comput
er. Thank you.
________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip
________________________________________
____________________________________
________
It's here! Your new message!
Get new email alerts with the free Yahoo! Toolbar.
http://tools.search.yahoo.com/toolbar/features/mail/
[ Post a follow-up to this message ]
| 
