Hi, I have just upgraded to debian testing (latest kernel) on my old
laptop. I hoped the newest kernel would solve this issue, but it's still
here.
I am trying to use a pcmcia (cardbus) usb 2.0 card.
It's found & usb driver are loaded. (see next). But when I connect an
usb2.0 device (such as dvb-t card) the laptop hangs until I remove the
card.
Googling I've found  a similar problem, and it pointed to the ehci.
disabling ehci (removing the kernel driver after plugging in the card)
solves the hangs. But this way I have a usb1.1 and I need a 2.0 for the tv
card.

any idea?

these are the log files:
lspci -n
06:00.0 0c03: 10b9:5237 (rev 03)
06:00.3 0c03: 10b9:5239 (rev 01)

lspci -v
06:00.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
 10 [OHCI])
Subsystem: ALi Corporation USB 1.1 Controller
Flags: bus master, 66MHz, medium devsel, latency 16, IRQ 11
Memory at 26000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2

06:00.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if
 20 [EHCI])
Subsystem: ALi Corporation USB 2.0 Controller
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
Memory at 26001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port

dmesg

pccard: CardBus card inserted into slot 1
PCI: Enabling device 0000:06:00.3 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.3[A] -> Link [LNKB] -> GSI 11 (level,
 low) -> IRQ 11
ehci_hcd 0000:06:00.3: EHCI Host Controller
ehci_hcd 0000:06:00.3: new USB bus registered, assigned bus number 2
ehci_hcd 0000:06:00.3: debug port 1
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ehci_hcd 0000:06:00.3: irq 11, io mem 0x26001000
ehci_hcd 0000:06:00.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKB] -> GSI 11 (level,
 low) -> IRQ 11
ohci_hcd 0000:06:00.0: OHCI Host Controller
ohci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:06:00.0: irq 11, io mem 0x26000000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected

cerebron-laptop:~# lspcmcia
Socket 0 Bridge:        [yenta_cardbus]         (bus ID: 0000:00:0b.0)
Socket 1 Bridge:        [yenta_cardbus]         (bus ID: 0000:00:0b.1)

thanks
Cits

[ Post a follow-up to this message ]