07-08-07 06:13 PM
<attachement...>
> scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0
ANSI: 5
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x64 (ATA bus error)
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 1:0:0:0: Attached scsi CD-ROM sr0
> ata_piix 0000:00:1f.2: version 2.00ac6
> ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
Looks like a dvd rw drive WAS detected at ata2.00 assigned to sr0
anfred Lutz wrote:
> Hi all!
>
> few days ago I installed Etch on my computer and am now stuck with the
> DVD writer. The installer had no issue booting from the drive and do the
> installation. But the installed system no longer detects that a DVD
> drive is there.
>
> The DVD is a SATA drive from LG, connected to a JMicron SATA/IDE JMB 363
> (according mainboard manual) controller. I'm wondering that the Etch
> installer was able to run this combination, whereas the Etch
> installation does not...
>
> Searching the net about that issue I'm even more wondering that the
> installation worked, after I read that support for the JMicron
> controller was introduced with 2.6.19. Don't get me wrong, I'm not
> complaining that the installation worked that smoothly... :-)
>
> Booting Knoppix 5.2 live CD works well, with the DVD being fine... but
> that's based on 2.6.19 anyway...
>
> Changing BIOS settings for the JMicron controller from IDE to AHCI
> didn't made a difference.
>
> Has anyone seen this before and ideas how to get Etch detect my DVD drive?
>
> Thanks & best regards,
> Manfred
>
>
> ------------------------------------------------------------------------
>
> Bootdata ok (command line is root=/dev/md0 ro )
> Linux version 2.6.18-4-amd64 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org)
(gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 2
6 11:36:53 CEST 2007
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
> BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
> BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
> BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> DMI 2.4 present.
> ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa
d70
> ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007
e790000
> ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x000000007
e790200
> ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x000000007
e790390
> ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x000000007
e790400
> ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x000000007
e790440
> ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x000000007
e79e040
> ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x000000007
e79a250
> ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x000000007
e79a288
> ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x000000007
e79e0c0
> ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x000000007
e7a00f0
> ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x000000007
e7a02b0
> ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x000000000
0000000
> No NUMA configuration found
> Faking a node at 0000000000000000-000000007e790000
> Bootmem setup node 0 0000000000000000-000000007e790000
> On node 0 totalpages: 509966
> DMA zone: 3056 pages, LIFO batch:0
> DMA32 zone: 506910 pages, LIFO batch:31
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Setting APIC routing to physical flat
> ACPI: HPET id: 0x8086a202 base: 0xfed00000
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
> SMP: Allowing 4 CPUs, 2 hotplug CPUs
> Built 1 zonelists. Total pages: 509966
> Kernel command line: root=/dev/md0 ro
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
> time.c: Detected 1866.670 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
> Checking aperture...
> Memory: 2030880k/2072128k available (1930k kernel code, 40860k reserved, 8
68k data, 176k init)
> Calibrating delay using timer specific routine.. 3736.72 BogoMIPS (lpj=747
3459)
> Security Framework v1.0.0 initialized
> SELinux: Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 256
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> using mwait in idle threads.
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU0: Thermal monitoring enabled (TM2)
> SMP alternatives: switching to UP code
> ACPI: Core revision 20060707
> Using local APIC timer interrupts.
> result 16666702
> Detected 16.666 MHz APIC timer.
> SMP alternatives: switching to SMP code
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3733.50 BogoMIPS (lpj=746
7000)
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU1: Thermal monitoring enabled (TM2)
> Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> Brought up 2 CPUs
> testing NMI watchdog ... OK.
> migration_cost=20
> checking if image is initramfs... it is
> Freeing initrd memory: 5661k freed
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
> PCI: Not using MMCONFIG.
> PCI: Using configuration type 1
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:00:02.0
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, di
sabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: ACPI device : hid PNP0A08
> pnp: ACPI device : hid PNP0C01
> pnp: ACPI device : hid PNP0200
> pnp: ACPI device : hid PNP0B00
> pnp: ACPI device : hid PNP0800
> pnp: ACPI device : hid PNP0C04
> pnp: ACPI device : hid PNP0501
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0103
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0303
> pnp: ACPI device : hid PNP0C02
> pnp: ACPI device : hid PNP0C01
> pnp: PnP ACPI: found 14 devices
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a re
port
> hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
> hpet0: 3 64-bit timers, 14318180 Hz
> PCI-GART: No AMD northbridge found.
> pnp: the driver 'system' has been registered
> pnp: match found with the PnP device '00:01' and the driver 'system'
> pnp: match found with the PnP device '00:07' and the driver 'system'
> pnp: 00:07: ioport range 0x290-0x297 has been reserved
> pnp: match found with the PnP device '00:08' and the driver 'system'
> pnp: match found with the PnP device '00:0a' and the driver 'system'
> pnp: match found with the PnP device '00:0c' and the driver 'system'
> pnp: match found with the PnP device '00:0d' and the driver 'system'
> PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
> PCI: Bridge: 0000:00:1c.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: bfe00000-bfefffff
> PCI: Bridge: 0000:00:1c.4
> IO window: a000-afff
> MEM window: ff400000-ff4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1e.0
> IO window: b000-bfff
> MEM window: ff500000-ff5fffff
> PREFETCH window: 80000000-800fffff
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> audit: initializing netlink socket (disabled)
> audit(1183842440.080:1): initialized
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.0:pcie00]
> Allocate Port Service[0000:00:1c.0:pcie02]
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.4:pcie00]
> Allocate Port Service[0000:00:1c.4:pcie02]
> Real Time Clock Driver v1.12ac
> hpet_resources: 0xfed00000 is busy
> Linux agpgart interface v0.101 (c) Dave Jones
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> pnp: the driver 'serial' has been registered
> pnp: match found with the PnP device '00:06' and the driver 'serial'
> 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
> pnp: the driver 'i8042 kbd' has been registered
> pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
> pnp: the driver 'i8042 aux' has been registered
> PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
> PNP: PS/2 controller doesn't have AUX irq; using default 12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> ACPI: (supports S0 S1 S3 S4 S5)
> Freeing unused kernel memory: 176k freed
> input: AT Translated Set 2 keyboard as /class/input/input0
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is no
t present [20060707]
> ACPI: Getting cpuindex for acpiid 0x3
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is no
t present [20060707]
> ACPI: Getting cpuindex for acpiid 0x4
> USB Universal Host Controller Interface driver v3.0
> GSI 17 sharing vector 0xC9 and IRQ 17
> ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 201
> PCI: Setting latency timer of device 0000:00:1a.0 to 64
> uhci_hcd 0000:00:1a.0: UHCI Host Controller
> uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
> uhci_hcd 0000:00:1a.0: irq 201, io base 0x0000d880
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=x
x
> ieee1394: Initialized config rom entry `ip1394'
> ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 169
> PCI: Setting latency timer of device 0000:00:1a.1 to 64
> uhci_hcd 0000:00:1a.1: UHCI Host Controller
> uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:1a.1: irq 169, io base 0x0000dc00
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> GSI 18 sharing vector 0xD1 and IRQ 18
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: UHCI Host Controller
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1d.0: irq 209, io base 0x0000d400
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> GSI 19 sharing vector 0xD9 and IRQ 19
> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: UHCI Host Controller
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1d.1: irq 217, io base 0x0000d480
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> GSI 20 sharing vector 0xE1 and IRQ 20
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 225
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: UHCI Host Controller
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
> uhci_hcd 0000:00:1d.2: irq 225, io base 0x0000d800
> usb usb5: configuration #1 chosen from 1 choice
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 225
> PCI: Setting latency timer of device 0000:00:1a.7 to 64
> ehci_hcd 0000:00:1a.7: EHCI Host Controller
> ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
> ehci_hcd 0000:00:1a.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1a.7
> ehci_hcd 0000:00:1a.7: irq 225, io mem 0xff9fb800
> ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb6: configuration #1 chosen from 1 choice
> hub 6-0:1.0: USB hub found
> hub 6-0:1.0: 4 ports detected
> ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 209
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: EHCI Host Controller
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
> ehci_hcd 0000:00:1d.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: irq 209, io mem 0xff9fb400
> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb7: configuration #1 chosen from 1 choice
> hub 7-0:1.0: USB hub found
> hub 7-0:1.0: 6 ports detected
> JMB363: IDE controller at PCI slot 0000:01:00.1
> PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
> ACPI: PCI Interrupt 0000:01:00.1[B] -> GSI 17 (level, low) -> IRQ 169
> JMB363: chipset revision 3
> JMB363: 100% native mode on irq 169
> PCI: Setting latency timer of device 0000:01:00.1 to 64
> ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:pio, hdh:pio
> Probing IDE interface ide2...
> usb 5-2: new low speed USB device using uhci_hcd and address 2
> Probing IDE interface ide3...
> usb 5-2: configuration #1 chosen from 1 choice
> usbcore: registered new driver hiddev
> input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
> input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-00
00:00:1d.2-2
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> GSI 21 sharing vector 0xE9 and IRQ 21
> ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 233
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233] MMIO=[ff5ff800
-ff5fffff] Max Packet=[2048] IR/IT contexts=[4/8]
> JMB361: IDE controller at PCI slot 0000:01:00.0
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201
> JMB361: chipset revision 3
> JMB361: 100% native mode on irq 201
> JMB361: dma_base is invalid
> ide0: JMB361 Bus-Master DMA disabled (BIOS)
> JMB361: dma_base is invalid
> ide1: JMB361 Bus-Master DMA disabled (BIOS)
> Probing IDE interface ide0...
> SCSI subsystem initialized
> libata version 2.00 loaded.
> Probing IDE interface ide1...
> ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 19 (level, low) -> IRQ 217
> skge 1.6 addr 0xff5f8000 irq 217 chip Yukon-Lite rev 9
> skge eth0: addr 00:1b:fc:7c:0a:bd
> ata_piix 0000:00:1f.2: version 2.00
> ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata1: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 217
> ata2: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 217
> scsi0 : ata_piix
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800015071d2]
> ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata1.00: ata1: dev 0 multi count 16
> ata1.00: configured for UDMA/133
> scsi1 : ata_piix
> ata2.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata2.00: ata2: dev 0 multi count 16
> ata2.00: configured for UDMA/133
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
> ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 217
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> ata3: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 217
> ata4: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 217
> scsi2 : ata_piix
> ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata3.00: ata3: dev 0 multi count 16
> ata3.00: configured for UDMA/133
> scsi3 : ata_piix
> ATA: abnormal status 0x7F on port 0xCC07
> Vendor: ATA Model: ST3320620AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3
> sd 0:0:0:0: Attached scsi disk sda
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> sdb: sdb1 sdb2 sdb3
> sd 1:0:0:0: Attached scsi disk sdb
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> sdc: sdc1 sdc2 sdc3
> sd 2:0:0:0: Attached scsi disk sdc
> Probing IDE interface ide0...
> Probing IDE interface ide1...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md: bitmap version 4.39
> md: raid1 personality registered for level 1
> raid5: automatically using best checksumming function: generic_sse
> generic_sse: 6839.000 MB/sec
> raid5: using function: generic_sse (6839.000 MB/sec)
> raid6: int64x1 1750 MB/s
> raid6: int64x2 2111 MB/s
> raid6: int64x4 2016 MB/s
> raid6: int64x8 1342 MB/s
> raid6: sse2x1 3208 MB/s
> raid6: sse2x2 3834 MB/s
> raid6: sse2x4 5546 MB/s
> raid6: using algorithm sse2x4 (5546 MB/s)
> md: raid6 personality registered for level 6
> md: raid5 personality registered for level 5
> md: raid4 personality registered for level 4
> md: md0 stopped.
> md: bind<sdb1>
> md: bind<sdc1>
> md: bind<sda1>
> raid1: raid set md0 active with 2 out of 2 mirrors
> md: md1 stopped.
> md: bind<sdb3>
> md: bind<sdc3>
> md: bind<sda3>
> raid5: device sda3 operational as raid disk 0
> raid5: device sdc3 operational as raid disk 2
> raid5: device sdb3 operational as raid disk 1
> raid5: allocated 3212kB for md1
> raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
> RAID5 conf printout:
> --- rd:3 wd:3 fd:0
> disk 0, o:1, dev:sda3
> disk 1, o:1, dev:sdb3
> disk 2, o:1, dev:sdc3
> device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redha
t.com
> Attempting manual resume
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> ts: Compaq touchscreen protocol output
> eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> input: PC Speaker as /class/input/input2
> PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
> ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 225
> GSI 22 sharing vector 0x32 and IRQ 22
> ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 50
> PCI: Setting latency timer of device 0000:00:1b.0 to 64
> hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
> Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
> Adding 979956k swap on /dev/sdb2. Priority:-2 extents:1 across:979956k
> Adding 979956k swap on /dev/sdc2. Priority:-3 extents:1 across:979956k
> EXT3 FS on md0, internal journal
> loop: loaded (max 8 devices)
> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
> ieee1394: sbp2: Try serialize_io=0 for better performance
> agpgart: Detected an Intel 965G Chipset.
> agpgart: Detected 7676K stolen memory.
> agpgart: AGP aperture is 512M @ 0xd0000000
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-0, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-4, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-5, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-2, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on dm-3, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> skge eth1: enabling interface
> skge eth1: Link is up at 100 Mbps, full duplex, flow control tx and rx
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> pnp: the driver 'parport_pc' has been registered
> lp: driver loaded but no devices found
> ppdev: user-space parallel port driver
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> IPv6 over IPv4 tunneling driver
> [drm] Initialized drm 1.0.1 20051102
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 201
> [drm] Initialized i915 1.5.0 20060119 on minor 0
> eth1: no IPv6 routers present
>
>
> ------------------------------------------------------------------------
>
> Linux version 2.6.19.5 (root@Knoppix) (gcc version 4.1.2 20061115 (prerele
ase) (Debian 4.1.1-21)) #4 SMP PREEMPT Sat Mar 3 02:19:32 CET 2007
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 000000007e790000 (usable)
> BIOS-e820: 000000007e790000 - 000000007e79e000 (ACPI data)
> BIOS-e820: 000000007e79e000 - 000000007e7e0000 (ACPI NVS)
> BIOS-e820: 000000007e7e0000 - 000000007e800000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
> 1127MB HIGHMEM available.
> 896MB LOWMEM available.
> found SMP MP-table at 000ff780
> Entering add_active_range(0, 0, 518032) 0 entries of 256 used
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 229376
> HighMem 229376 -> 518032
> early_node_map[1] active PFN ranges
> 0: 0 -> 518032
> On node 0 totalpages: 518032
> DMA zone: 32 pages used for memmap
> DMA zone: 0 pages reserved
> DMA zone: 4064 pages, LIFO batch:0
> Normal zone: 1760 pages used for memmap
> Normal zone: 223520 pages, LIFO batch:31
> HighMem zone: 2255 pages used for memmap
> HighMem zone: 286401 pages, LIFO batch:31
> DMI 2.4 present.
> ACPI: RSDP (v000 ACPIAM ) @ 0x000fad70
> ACPI: RSDT (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790000
> ACPI: FADT (v002 MSTEST OEMFACP 0x03000719 MSFT 0x00000097) @ 0x7e790200
> ACPI: MADT (v001 MSTEST OEMAPIC 0x03000719 MSFT 0x00000097) @ 0x7e790390
> ACPI: MCFG (v001 MSTEST OEMMCFG 0x03000719 MSFT 0x00000097) @ 0x7e790400
> ACPI: SLIC (v001 NEC 0x03000719 MSFT 0x00000097) @ 0x7e790440
> ACPI: OEMB (v001 MSTEST AMI_OEM 0x03000719 MSFT 0x00000097) @ 0x7e79e040
> ACPI: HPET (v001 MSTEST OEMHPET 0x03000719 MSFT 0x00000097) @ 0x7e79a250
> ACPI: ASF! (v032 LEGEND I865PASF 0x00000001 INTL 0x20060113) @ 0x7e79a288
> ACPI: GSCI (v001 MSTEST GMCHSCI 0x03000719 MSFT 0x00000097) @ 0x7e79e0c0
> ACPI: SSDT (v001 AMI CPU1PM 0x00000001 INTL 0x20060113) @ 0x7e7a00f0
> ACPI: SSDT (v001 AMI CPU2PM 0x00000001 INTL 0x20060113) @ 0x7e7a02b0
> ACPI: DSDT (v001 A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x00000000
> ACPI: PM-Timer IO Port: 0x808
> ACPI: Local APIC address 0xfee00000
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
> Processor #0 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
> Processor #1 6:15 APIC version 20
> ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
> ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
> ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
> ACPI: IRQ0 used by override.
> ACPI: IRQ2 used by override.
> ACPI: IRQ9 used by override.
> Enabling APIC mode: Flat. Using 1 I/O APICs
> ACPI: HPET id: 0x8086a202 base: 0xfed00000
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at 80000000 (gap: 7e800000:80600000)
> Detected 1866.736 MHz processor.
> Built 1 zonelists. Total pages: 513985
> Kernel command line: ramdisk_size=100000 init=/etc/init lang=de apm=power-
off vga=791 initrd=minirt.gz nomce loglevel=0 libata.atapi_enabled=1 quiet n
mi_watchdog=0 BOOT_IMAGE=knoppix BOOT_IMAGE=linux
> mapped APIC to ffffd000 (fee00000)
> mapped IOAPIC to ffffc000 (fec00000)
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 16384 bytes)
> Console: colour dummy device 80x25
> Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Memory: 2048256k/2072128k available (2748k kernel code, 22668k reserved, 9
56k data, 336k init, 1154624k highmem)
> virtual kernel memory layout:
> fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
> pkmap : 0xff800000 - 0xffc00000 (4096 kB)
> vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
> lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
> .init : 0xc04a6000 - 0xc04fa000 ( 336 kB)
> .data : 0xc03af3bc - 0xc049e7b4 ( 956 kB)
> .text : 0xc0100000 - 0xc03af3bc (2748 kB)
> Checking if this processor honours the WP bit even in supervisor mode... O
k.
> Using HPET for base-timer
> Calibrating delay using timer specific routine.. 3736.14 BogoMIPS (lpj=747
2281)
> Security Framework v1.0.0 initialized
> SELinux: Disabled at boot.
> Capability LSM initialized
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 000
0e3bd 00000000 00000001
> monitor/mwait feature present.
> using mwait in idle threads.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 0
> CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 0
0000000 00000001
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> Checking for popad bug... OK.
> SMP alternatives: switching to UP code
> ACPI: Core revision 20060707
> CPU0: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> SMP alternatives: switching to SMP code
> Booting processor 1/1 eip 3000
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3733.42 BogoMIPS (lpj=746
6847)
> CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 000
0e3bd 00000000 00000001
> monitor/mwait feature present.
> CPU: L1 I cache: 32K, L1 D cache: 32K
> CPU: L2 cache: 4096K
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0000e3bd 0
0000000 00000001
> CPU1: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz stepping 06
> Total of 2 processors activated (7469.56 BogoMIPS).
> ENABLING IO-APIC IRQs
> ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
> checking TSC synchronization across 2 CPUs: passed.
> Brought up 2 CPUs
> migration_cost=665
> checking if image is initramfs...it isn't (no cpio magic); looks like an i
nitrd
> Freeing initrd memory: 1189k freed
> NET: Registered protocol family 16
> EISA bus registered
> ACPI: bus type pci registered
> PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
> PCI: Not using MMCONFIG.
> PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:00:02.0
> PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
> PCI quirk: region 0480-04bf claimed by ICH6 GPIO
> PCI: Transparent bridge - 0000:00:1e.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, di
sabled.
> ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
> ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 14 devices
> PnPBIOS: Disabled by ACPI PNP
> SCSI subsystem initialized
> libata version 2.00 loaded.
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a re
port
> NetLabel: Initializing
> NetLabel: domain hash size = 128
> NetLabel: protocols = UNLABELED CIPSOv4
> NetLabel: unlabeled traffic allowed by default
> pnp: 00:07: ioport range 0x290-0x297 has been reserved
> PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
> PCI: Bridge: 0000:00:1c.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: bfe00000-bfefffff
> PCI: Bridge: 0000:00:1c.4
> IO window: a000-afff
> MEM window: ff400000-ff4fffff
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:1e.0
> IO window: b000-bfff
> MEM window: ff500000-ff5fffff
> PREFETCH window: 80000000-800fffff
> ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> PCI: Setting latency timer of device 0000:00:1e.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
> TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
> TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
> TCP: Hash tables configured (established 131072 bind 65536)
> TCP reno registered
> audit: initializing netlink socket (disabled)
> audit(1183842679.792:1): initialized
> highmem bounce pool size: 64 pages
> Total HugeTLB memory allocated, 0
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> fuse init (API version 7.8)
> fuse distribution version: 2.6.1
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered (default)
> io scheduler cfq registered
> PCI: Setting latency timer of device 0000:00:1c.0 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.0:pcie00]
> Allocate Port Service[0000:00:1c.0:pcie02]
> PCI: Setting latency timer of device 0000:00:1c.4 to 64
> assign_interrupt_mode Found MSI capability
> Allocate Port Service[0000:00:1c.4:pcie00]
> Allocate Port Service[0000:00:1c.4:pcie02]
> vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3072k, tota
l 7616k
> vesafb: mode is 1024x768x16, linelength=2048, pages=3
> vesafb: protected mode interface info at 00ff:44f0
> vesafb: scrolling: redraw
> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
> Console: switching to colour frame buffer device 128x48
> fb0: VESA VGA frame buffer device
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Real Time Clock Driver v1.12ac
> floppy0: no floppy controllers found
> RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=x
x
> JMB363: IDE controller at PCI slot 0000:01:00.1
> PCI: Enabling device 0000:01:00.1 (0000 -> 0001)
> ACPI: PCI Interrupt 0000:01:00.1[B] -> GSI 17 (level, low) -> IRQ 16
> JMB363: chipset revision 3
> JMB363: 100% native mode on irq 16
> PCI: Setting latency timer of device 0000:01:00.1 to 64
> ide2: BM-DMA at 0xa400-0xa407, BIOS settings: hde:pio, hdf:pio
> ide3: BM-DMA at 0xa408-0xa40f, BIOS settings: hdg:DMA, hdh:DMA
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Probing IDE interface ide0...
> Probing IDE interface ide1...
> Probing IDE interface ide2...
> Probing IDE interface ide3...
> Loading iSCSI transport class v2.0-724.<7>ahci 0000:01:00.0: version 2.0
> ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:01:00.0 to 64
> ahci 0000:01:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mo
de
> ahci 0000:01:00.0: flags: 64bit ncq pm led clo pmp pio slum part
> ata1: SATA max UDMA/133 cmd 0xF8828100 ctl 0x0 bmdma 0x0 irq 17
> ata2: SATA max UDMA/133 cmd 0xF8828180 ctl 0x0 bmdma 0x0 irq 17
> scsi0 : ahci
> ata1: SATA link down (SStatus 0 SControl 300)
> scsi1 : ahci
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: ATAPI, max UDMA/100
> ata2.00: configured for UDMA/100
> scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-H62N CL00 PQ: 0 ANSI:
5
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x64 (ATA bus error)
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.20
> sr 1:0:0:0: Attached scsi CD-ROM sr0
> ata_piix 0000:00:1f.2: version 2.00ac6
> ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1f.2 to 64
> ata3: SATA max UDMA/133 cmd 0xE880 ctl 0xE802 bmdma 0xE080 irq 18
> ata4: SATA max UDMA/133 cmd 0xE480 ctl 0xE402 bmdma 0xE088 irq 18
> scsi2 : ata_piix
> ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata3.00: ata3: dev 0 multi count 16
> ata3.00: configured for UDMA/133
> scsi3 : ata_piix
> ata4.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata4.00: ata4: dev 0 multi count 16
> ata4.00: configured for UDMA/133
> scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI:
5
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3
> sd 2:0:0:0: Attached scsi disk sda
> scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI:
5
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> SCSI device sdb: 625142448 512-byte hdwr sectors (320073 MB)
> sdb: Write Protect is off
> sdb: Mode Sense: 00 3a 00 00
> SCSI device sdb: drive cache: write back
> sdb: sdb1 sdb2 sdb3
> sd 3:0:0:0: Attached scsi disk sdb
> ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
> ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1f.5 to 64
> ata5: SATA max UDMA/133 cmd 0xD080 ctl 0xD002 bmdma 0xC800 irq 18
> ata6: SATA max UDMA/133 cmd 0xCC00 ctl 0xC882 bmdma 0xC808 irq 18
> scsi4 : ata_piix
> ata5.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32)
> ata5.00: ata5: dev 0 multi count 16
> ata5.00: configured for UDMA/133
> scsi5 : ata_piix
> ATA: abnormal status 0x7F on port 0xCC07
> scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI:
5
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB)
> sdc: Write Protect is off
> sdc: Mode Sense: 00 3a 00 00
> SCSI device sdc: drive cache: write back
> sdc: sdc1 sdc2 sdc3
> sd 4:0:0:0: Attached scsi disk sdc
> PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
> PNP: PS/2 controller doesn't have AUX irq; using default 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> EISA: Probing bus 0 at eisa.0
> EISA: Detected 0 cards.
> Initializing XFRM netlink socket
> NET: Registered protocol family 1
> NET: Registered protocol family 15
> Using IPI No-Shortcut mode
> ACPI: (supports S0 S1 S3 S4 S5)
> Time: tsc clocksource has been installed.
> input: AT Translated Set 2 keyboard as /class/input/input0
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem).
> Failed initialization of WD-7000 SCSI card!
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1a.7 to 64
> ehci_hcd 0000:00:1a.7: EHCI Host Controller
> ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:1a.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1a.7
> ehci_hcd 0000:00:1a.7: irq 19, io mem 0xff9fb800
> ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
> PCI: Setting latency timer of device 0000:00:1d.7 to 64
> ehci_hcd 0000:00:1d.7: EHCI Host Controller
> ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
> ehci_hcd 0000:00:1d.7: debug port 1
> PCI: cache line size of 32 is not supported by device 0000:00:1d.7
> ehci_hcd 0000:00:1d.7: irq 20, io mem 0xff9fb400
> ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 6 ports detected
> USB Universal Host Controller Interface driver v3.0
> ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17
> PCI: Setting latency timer of device 0000:00:1a.0 to 64
> uhci_hcd 0000:00:1a.0: UHCI Host Controller
> uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:1a.0: irq 17, io base 0x0000d880
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 16
> PCI: Setting latency timer of device 0000:00:1a.1 to 64
> uhci_hcd 0000:00:1a.1: UHCI Host Controller
> uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
> uhci_hcd 0000:00:1a.1: irq 16, io base 0x0000dc00
> usb usb4: configuration #1 chosen from 1 choice
> hub 4-0:1.0: USB hub found
> hub 4-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
> PCI: Setting latency timer of device 0000:00:1d.0 to 64
> uhci_hcd 0000:00:1d.0: UHCI Host Controller
> uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
> uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000d400
> usb usb5: configuration #1 chosen from 1 choice
> hub 5-0:1.0: USB hub found
> hub 5-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
> PCI: Setting latency timer of device 0000:00:1d.1 to 64
> uhci_hcd 0000:00:1d.1: UHCI Host Controller
> uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
> uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000d480
> usb usb6: configuration #1 chosen from 1 choice
> hub 6-0:1.0: USB hub found
> hub 6-0:1.0: 2 ports detected
> ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
> PCI: Setting latency timer of device 0000:00:1d.2 to 64
> uhci_hcd 0000:00:1d.2: UHCI Host Controller
> uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
> uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000d800
> usb usb7: configuration #1 chosen from 1 choice
> hub 7-0:1.0: USB hub found
> hub 7-0:1.0: 2 ports detected
> ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI
)
> usb 7-2: new low speed USB device using uhci_hcd and address 2
> usb 7-2: configuration #1 chosen from 1 choice
> usbcore: registered new interface driver libusual
> usbcore: registered new interface driver hiddev
> input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
> input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-00
00:00:1d.2-2
> usbcore: registered new interface driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> Initializing USB Mass Storage driver...
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> ieee1394: Initialized config rom entry `ip1394'
> ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 21 (level, low) -> IRQ 21
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[ff5ff800-
ff5fffff] Max Packet=[2048] IR/IT contexts=[4/8]
> ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
> ieee1394: sbp2: Try serialize_io=0 for better performance
> ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800015071d2]
> ISO 9660 Extensions: Microsoft Joliet Level 3
> ISO 9660 Extensions: RRIP_1991A
> cloop: Initializing cloop v2.06
> cloop: loaded (max 8 devices)
> cloop: /cdrom/KNOPPIX/KNOPPIX: 49667 blocks, 131072 bytes/block, largest b
lock is 131118 bytes.
> cloop: loaded 256 blocks into cache.
> ISO 9660 Extensions: RRIP_1991A
> cloop: losetup_file: 38179 blocks, 131072 bytes/block, largest block is 13
1118 bytes.
> cloop: loaded 256 blocks into cache.
> ISO 9660 Extensions: RRIP_1991A
> aufs 20070226
> Freeing unused kernel memory: 336k freed
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> Using specific hotkey driver
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is no
t present [20060707]
> ACPI: Getting cpuindex for acpiid 0x3
> ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is no
t present [20060707]
> ACPI: Getting cpuindex for acpiid 0x4
> cpufreq: No nForce2 chipset.
> p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to <li
nux@brodo.de>
> p4-clockmod: Unknown p4-clockmod-capable CPU. Please send an e-mail to <li
nux@brodo.de>
> powernow: This module only works with AMD K7 CPUs
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x54 (ATA bus error)
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
> ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
> ata2.00: (irq_stat 0x48000000, interface fatal error)
> ata2.00: tag 0 cmd 0xa0 Emask 0x50 stat 0x51 err 0x54 (ATA bus error)
> sr 1:0:0:0: Attached scsi generic sg0 type 5
> sd 2:0:0:0: Attached scsi generic sg1 type 0
> sd 3:0:0:0: Attached scsi generic sg2 type 0
> sd 4:0:0:0: Attached scsi generic sg3 type 0
> ata2: soft resetting port
> ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata2.00: configured for UDMA/100
> ata2: EH complete
> PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
> ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 19
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected an Intel 965G Chipset.
> agpgart: Detected 7676K stolen memory.
> agpgart: AGP aperture is 512M @ 0xd0000000
> ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 19 (level, low) -> IRQ 18
> skge 1.9 addr 0xff5f8000 irq 18 chip Yukon-Lite rev 9
> skge eth1: addr 00:1b:fc:7c:0a:bd
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
> PCI: Setting latency timer of device 0000:00:1b.0 to 64
> hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
> device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redh
at.com
> Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
> Adding 979956k swap on /dev/sdb2. Priority:-2 extents:1 across:979956k
> Adding 979956k swap on /dev/sdc2. Priority:-3 extents:1 across:979956k
> NET: Registered protocol family 17
> skge eth1: enabling interface
> skge eth1: Link is up at 100 Mbps, full duplex, flow control both
> [drm] Initialized drm 1.0.1 20051102
> NET: Registered protocol family 10
> lo: Disabled Privacy Extensions
> Mobile IPv6
> ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
> [drm] Initialized i915 1.5.0 20060119 on minor 0
> eth1: no IPv6 routers present
> skge eth1: disabling interface
> skge eth1: enabling interface
> skge eth1: Link is up at 100 Mbps, full duplex, flow control both
> eth1: no IPv6 routers present
[ Post a follow-up to this message ]
|
