09-03-07 06:11 PM
Rajil Saraswat explained :
> Hi All,
>
> I am trying to get the call waiting feature to work on my PAP2. I have
> modified the Regional settings to UK ones which are listed here
> http://www.provu.co.uk/pdf/sipura/s...al_settings.pdf
>
> Using the above settings I do get beeps and CID of the waiting call.
> However, if i press R on my phone it doesnt changeover to the waiting call
.
> I just get a brief tone something like a flash tone.
>
> Has anybody managed to pickup waiting call on PAP2? I will be very
> interested to know your PAP2 settings.
>
> Cheers
> Rajil
Posted elsewhere by {{{{welcome}}}}}:
Under Regional Tab.
Dial Tone: 350@-19,440@-22;60(*/0/1+2)
Second Dial Tone: 420@-19,520@-19;10(*/0/1+2)
Outside Dial Tone: 420@-16;10(*/0/1)
Prompt Tone: 520@-19,620@-19;10(*/0/1+2)
Busy Tone: 400@-10;30(.375/.375/1)
Reorder Tone: 400@-20;20(*/0/1)
Off Hook Warning Tone: 480@-10,620@0;90(.125/.125/1+2)
Ring Back Tone: 400@-20,450@-20;*(.4/.2/1+2,.4/2/1+2)
Confirm Tone: 600@-16;1(.25/.25/1)
SIT1 Tone: 950@-16,1400@-16,1800@-16;20(.330/0/1,.330/0/2,.330/0/3,0/1/0)
SIT2 Tone: 914@-16,1371@-16,1777@-16;20(.274/0/1,.274/0/2,.380/0/3,0/4/0)
SIT3 Tone: 914@-16,1371@-16,1777@-16;20(.380/0/1,.380/0/2,.380/0/3,0/4/0)
SIT4 Tone: 985@-16,1371@-16,1777@-16;20(.380/0/1,.274/0/2,.380/0/3,0/4/0)
MWI Dial Tone: 350@-19,440@-22;10(.75/.75/1+2)
Cfwd Dial Tone: 350@-19,440@-19;2(.2/.2/1+2);10(*/0/1+2)
DND Dial Tone: 350@-19,440@-19;2(.2/.2/2);10(*/0/1+2)
Holding Tone: 600@-19;*(.1/.1/1,.1/.1/1,.1/9.5/1)
Conference Tone: 350@-19;20(.1/.1/1,.1/9.7/1)
Secure Call Indication Tone: 397@-19,507@-19;15(0/2/0,.2/.1/1,.1/2.1/2)
Feature Invocation Tone: 350@-16;*(.1/.1/1)
Ring1 Cadence: 60(.4/.2,.4/2)
Ring2 Cadence: 60(1/2)
Ring3 Cadence: 60(.25/.25,.25/.25,.25/1.75)
...
CWT1 Cadence: 30(.2/.2,.2/4.4)
Ring Waveform: Sinusoid (though Trapezoid may help problematic phones to rin
g).
Ring Frequency: 25
Ring Voltage: 80 (You can use 70, if problems try 75, 80, 85, 90)
CWT Frequency: 425@-20
Synchronized Ring: Yes
Hook Flash Timer Min: .06
Hook Flash Timer Max: .2
Callee On Hook Delay: 0
Reorder Delay: 5
Call Back Expires: 1800
Call Back Retry Intvl: 30
Call Back Delay: .5
VMWI Refresh Intvl: 0
Interdigit Long Timer: 10
Interdigit Short Timer: 3
CPC Delay: .5
CPC Duration: .1
...
Time Zone: GMT
FXS Port Impedance: 370+620||310nF
Daylight Saving Time Rule: start=3/-1/7/2:0:0;end=10/-1/7/2:0:0;save=1:0:0
DTMF Playback Level: -16
DTMF Playback Length: .25
Caller ID Method: ETSI FSK With PR(UK)
FXS Port Power Limit: 3
Caller ID FSK Standard: v.23
Feature Invocation Method: Default
More Echo Suppression: yes
In Line 1 (or Line 2)
Line Enable: yes
NAT Mapping Enable: yes
NAT Keep Alive Enable: yes
Network Jitter Level: low (Depends on how good your broadband is / route to
VoIP server)
Jitter Buffer Adjustment: Up and Down
Proxy and Registration
Proxy: Your Voip Proxy address (for example sip1.sipdiscount.com or sip.voip
cheap.com or sipgate.co.uk etc)
Subscriber Information - (where you enter your VoIP Account details).
Supplementary Service Subscription - This is where you enable services such
as Call Waiting, 3-Way Calling, block anonymous caller etc)
Audio Configuration - This is where you set-up which codecs you want to use
or only use.
If you have limited broadband speed (mostly if upload is poor) then you prob
ably only use one or more from G729a, G723 or G726)
If you want the best quality line, then you'd choose G711a (which is the sta
ndard used on a standard line)
(Myself, I use G711a only, have that set to my preferred codec and use that
one only, but you may find other codecs are fine).
DTMF Tx Method: (This will depend on the VoIP service you use, trial and err
or and depends on codec) Soon know if it don't work when you
try telephone banking for example and it doesn't recognise what numbers you
are pressing).
Hook Flash Tx Method: None
[ Post a follow-up to this message ]
| 
