Re: URGENT -- Blocking/Routing calls based on Caller

Would that be this one??

I've never really known if this is supported, nor am I clear on how to
use it...

# ani_filter.tcl
# Script Version 1.0(1)
#------------------------------------------------------------------ 
# October 2002, Niels Brunsgaard
# 
# Copyright (c) 1998-2002 by cisco Systems, Inc. 
# All rights reserved. 
#------------------------------------------------------------------ 
# 
# This tcl script filters calls based on ANI. If there is a match #
against a pe-configured list of numbers it changes the DNIS # to a
configurable value # 
# 

proc init { } { 
global param 
} 

proc act_Setup { } { 

leg setupack leg_incoming 

set dnis [infotag get leg_dnis]
set new_dnis [infotag get cfg_avpair new_dest]
set ani [infotag get leg_ani]
set ani_deny ""
set ani_pi [infotag get leg_ani_pi]
puts "dnis $dnis new_dnis $new_dnis ani $ani ani_pi $ani_pi"
if { $ani_pi != "presentation_allowed" } {
set ani ""
}

set x 1
while {1} {
if {[infotag get cfg_avpair_exists clid$x]} {
set ani_deny [infotag get cfg_avpair clid$x]
puts "clid$x = $ani_deny"
if { $ani == $ani_deny} {
set dnis $new_dnis
puts "match clid $ani_deny x=$x"
break
}
} else {
puts "No more clid at $x"
break
}
incr x
if { $x > 1000 } { puts "Too many clids" }
}
puts "Final dnis $dnis"
leg proceeding leg_incoming
leg setup $dnis callInfo leg_incoming
} 

proc act_CallSetupDone { } { 
global beep 

set status [infotag get evt_status] 

puts "Entering act_CallSetupDone"
if { $status != "ls_000"} { 
puts "Call [infotag get con_all] got event $status while placing
an outgoing call" 
call close 
} 
} 

proc act_Cleanup { } { 
puts "Entering act_Cleanup"
call close 
} 

proc act_Abort { } { 
puts "Unexpected event - entering act_Abort"
call close 
} 

init

#---------------------------------- 
#   State Machine 
#---------------------------------- 
set TopFSM(any_state,ev_disconnected) "act_Abort,same_state" 
set TopFSM(CALL_INIT,ev_setup_indication) "act_Setup,PLACECALL" 
set TopFSM(PLACECALL,ev_setup_done)  "act_CallSetupDone,CALLACTIVE" 
set TopFSM(CALLACTIVE,ev_disconnected)
"act_Cleanup,CALLDISCONNECTED" 
set  TopFSM(CALLDISCONNECTED,ev_disconnect_do
ne)
"act_Cleanup,same_state" 

fsm define TopFSM  CALL_INIT 

Tim Reimers 
Assistant Network Administrator 
Asheville City Schools 
Desk- 828-350-6195 Mobile-828-545-3104
fax- 828-255-5454 

Most days, there are several fires burning at once. Some days, what's
burning is your fire extinguisher.
To err is human; to truly screw it up requires the root password.

________________________________

From: Mike Reilly [mailto:reillyipt@gmail.com] 
Sent: Thursday, September 20, 2007 4:18 PM
To: Tim Reimers; cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] URGENT -- Blocking/Routing calls based on
Caller ID with CCM

There is a tcl script that can be used to route these calls to let's say
a callhandler in unity.

On 9/20/07 1:08 PM, "Tim Reimers" <tim.reimers@asheville.k12.nc.us>
wrote:

Blocking/Routing calls based on Caller ID with CCM

Is there any functionality for this in CCM 4.12 ???

We do not have IPCC or anything like that, unless there's a
'lite' version inside CCM that I'm not aware of.

We're receiving bomb threats repeatedly at a highschool, and
need to either block or route calls with no Caller ID or with known
numbers.

We could either route the calls to an announce-only mailbox
telling people to enable CallerID and call us back, or simply drop the
calls.

Tim Reimers 
Assistant Network Administrator 
Asheville City Schools 
Desk- 828-350-6195 Mobile-828-545-3104
fax- 828-255-5454 

Most days, there are several fires burning at once. Some days,
what's burning is your fire extinguisher.
To err is human; to truly screw it up requires the root
password.

________________________________

 ________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip