Re: Antw: Analog phones cant transfer calls
Web Server forum
Back To The Forum Home!Search!Private Messaging System

Web Server Talk Web Server Talk > WebserverTalk Community > Voice Over IP > Voice over IP Cisco > Re: Antw: Analog phones cant transfer calls




  Last Thread   Next Thread Next
  Show Printable Version Email this Page Subscribe to this Thread      Post New Thread    Post A Reply      

    Re: Antw: Analog phones cant transfer calls  
Lelio Fulgenzi


View Ip Address Report This Message To A Moderator Edit/Delete Message


 
09-21-07 12:11 PM

i'm guessing you press the flash button on the phone and then the feature co
de. something similar to the vg248.

----- Original Message ----- 
From: Jason Aarons (US) 
To: Ted Nugent ; Lelio Fulgenzi 
Cc: cisco-voip@puck.nether.net 
Sent: Thursday, September 20, 2007 11:57 PM
Subject: RE: [cisco-voip] Antw: Analog phones cant transfer calls on2811
acting asH323 gw to UCM 4.2 (3)


How are you supposed to transfer a call using an analog phone on a VG224 tha
t is SCCP? Can this be done? I didn't realize it was a feature!

 

From: cisco-voip-bounces@puck.nether.net [mailto:cisco-voip-bounces@puck
.nether.net] On Behalf Of Ted Nugent
Sent: Thursday, September 20, 2007 11:45 PM
To: Lelio Fulgenzi
Cc: cisco-voip@puck.nether.net
Subject: Re: [cisco-voip] Antw: Analog phones cant transfer calls on2811
acting asH323 gw to UCM 4.2 (3)

 

Yep same here and I wondered about that also until i tried to add an ISR FXS
 SCCP port to CM 4.1... its not an option like in 5.1 for example, I'm guess
ing thats what they're referring to...?


 

On 9/20/07, Lelio Fulgenzi <lelio@uoguelph.ca> wrote: 

I think the documentation is misleading...I'm using supplementary services w
/ SCCP on the VG224 with CCM 4.1(3) with no problems.

----- Original Message ----- 

From: Ted Nugent 

To: Cucumber Green 

Cc: cisco-voip@puck.nether.net 

Sent: Thursday, September 20, 2007 10:21 PM

Subject: Re: [cisco-voip] Antw: Analog phones cant transfer calls on 281
1acting asH323 gw to UCM 4.2 (3)


 

If you need features with fxs you might want to look into SCCP for FXS contr
oller as you would with a VG224 and h323 for and PSTN/PRI access etc. (see t
he link you need CM4.2+ and a certain rev of IOS depending on your hardware)
. 

 

http://www.cisco.com/en/US/partner/....html#wp1304455 

 

 

 



 

On 9/20/07, Cucumber Green <greencucumber2007@yahoo.com > wrote: 

Hello!

 

Yeah I have tried this without luck, I guess it only works if the H323 gatew
ay has a FXO

connection to a PBX

Robert Schuknecht <rschuknecht@gmx.de> wrote: 

Hi Cucumber,

did you try to adjust the the hook-flash timer under the voice-port?
This timer has to equal on the voice-port and the connected telephone. 

/Robert
 


September 2007 um 17:53 in Nachricht  3ab0adee131ef58c7afb0ea50017a410:[vbcol=
seagreen]
> Analog phones can send and receive calls from IP phones, but
> when pressing the hookflash key at the analog phone, the analog phone does
 
> not get a dial tone in order to transfer the call 
> 
> Phones are hooked into FXS ports on a 2811 and will use G729 codec.
> 
> I have already checked the "Media Termination Point required" check box in
 
> the gateway configuration at call manager (using unified call manager 4.2(
3) 
> ). I thought that would do the trick, but it didnt, any ideas?
> 
> This is the gateway config (IOS version 12.4(3g) spservicesK9) 
> 
> !
> version 12.4
> service timestamps debug datetime msec
> service timestamps log datetime msec
> service password-encryption
> !
> ip subnet-zero
> !
> ! 
> ip cef
> !
> !
> no ip domain lookup
> !
> voice-card 0
> no dspfarm
> !
> !
> !
> !
> interface Loopback0
> ip address X.X.X.X 255.255.255.255
> h323-gateway voip bind srcaddr X.X.X.X
> !
> !
> ip classless
> ip route 0.0.0.0 0.0.0.0 X.X.X.X 254
> !
> !
> control-plane
> !
> !
> !
> voice-port 0/1/0 
> signal loopStart
> !
> voice-port 0/1/1
> signal loopStart
> !
> dial-peer voice 10 pots
> destination-pattern 50001
> port 0/1/0
> !
> dial-peer voice 20 pots 
> destination-pattern 50002
> port 0/1/1
> !
> dial-peer voice 1 voip
> preference 1
> destination-pattern 1...
> session target ipv4:X.X.X.X
> dtmf-relay h245-alphanumeric 
> codec g729r8 bytes 40
> ip qos dscp cs3 media
> ip qos dscp cs3 signaling
> !
> dial-peer voice 4 voip
> preference 2
> destination-pattern 1...
> session target ipv4:X.X.X.X 
> dtmf-relay h245-alphanumeric
> codec g729r8 bytes 40
> ip qos dscp cs3 media
> ip qos dscp cs3 signaling
> !
> 
> 
> 
> ---------------------------------
> Be a better Globetrotter. Get better travel answers from someone who knows
. 
> Yahoo! Answers - Check it out.

 


----------------------------------------------------------------------------

Don't let your dream ride pass you by. Make it a reality with Yahoo! Autos. 


 ________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip

 


----------------------------------------------------------------------------

 ________________________________________
_______
cisco-voip mailing list
cisco-voip@puck.nether.net 
https://puck.nether.net/mailman/listinfo/cisco-voip 

 



----------------------------------------------------------------------------
--


Disclaimer: This e-mail communication and any attachments may contain confid
ential and privileged information and is for use by the designated addressee
(s) named above only. If you are not the intended addressee, you are hereby 
notified that you have received this communication in error and that any use
 or reproduction of this email or its contents is strictly prohibited and ma
y be unlawful. If you have received this communication in error, please noti
fy us immediately by replying to this message and deleting it from your comp
uter. Thank you. 






[ Post a follow-up to this message ]



    Sponsored Links  




 





   All times are GMT. The time now is 03:03 PM.      Post New Thread    Post A Reply      
  Last Thread   Next Thread Next


Most Popular forums 

Forum Jump:
Rate This Thread:

Forum Rules:
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is OFF
vB code is ON
Smilies are ON
[IMG] code is OFF
 
Medical and Health forum | Computer Games Reviews | Graphics design forum

Back To The Top
Home | Usercp | Faq | Register